4 The Global Command Engine (GCE) is used to help read/write registers with
5 critical time limitation, such as updating display configuration during the
6 vblank. The GCE can be used to implement the Command Queue (CMDQ) driver.
8 CMDQ driver uses mailbox framework for communication. Please refer to
9 mailbox.txt for generic information about mailbox device-tree bindings.
12 - compatible: can be "mediatek,mt8173-gce", "mediatek,mt8183-gce",
13 "mediatek,mt8186-gce", "mediatek,mt8192-gce", "mediatek,mt8195-gce" or
14 "mediatek,mt6779-gce".
15 - reg: Address range of the GCE unit
16 - interrupts: The interrupt signal from the GCE block
17 - clock: Clocks according to the common clock binding
18 - clock-names: Must be "gce" to stand for GCE clock
19 - #mbox-cells: Should be 2.
20 <&phandle channel priority>
21 phandle: Label name of a gce node.
22 channel: Channel of mailbox. Be equal to the thread id of GCE.
23 priority: Priority of GCE thread.
25 Required properties for a client device:
26 - mboxes: Client use mailbox to communicate with GCE, it should have this
27 property and list of phandle, mailbox specifiers.
28 Optional properties for a client device:
29 - mediatek,gce-client-reg: Specify the sub-system id which is corresponding
30 to the register address, it should have this property and list of phandle,
31 sub-system specifiers.
32 <&phandle subsys_number start_offset size>
33 phandle: Label name of a gce node.
34 subsys_number: specify the sub-system id which is corresponding
35 to the register address.
36 start_offset: the start offset of register address that GCE can access.
37 size: the total size of register address that GCE can access.
39 Optional properties for a client mutex node:
40 - mediatek,gce-events: GCE events used by clients. The event numbers are
41 defined in 'dt-bindings/gce/<chip>-gce.h'.
43 Some vaules of properties are defined in 'dt-bindings/gce/mt8173-gce.h',
44 'dt-bindings/gce/mt8183-gce.h', 'dt-bindings/gce/mt8186-gce.h'
45 'dt-bindings/gce/mt8192-gce.h', 'dt-bindings/gce/mt8195-gce.h' or
46 'dt-bindings/gce/mt6779-gce.h'.
47 Such as sub-system ids, thread priority, event ids.
52 compatible = "mediatek,mt8173-gce";
53 reg = <0 0x10212000 0 0x1000>;
54 interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_LOW>;
55 clocks = <&infracfg CLK_INFRA_GCE>;
60 Example for a client device:
62 mmsys: clock-controller@14000000 {
63 compatible = "mediatek,mt8173-mmsys";
64 mboxes = <&gce 0 CMDQ_THR_PRIO_LOWEST>,
65 <&gce 1 CMDQ_THR_PRIO_LOWEST>;
66 mutex-event-eof = <CMDQ_EVENT_MUTEX0_STREAM_EOF
67 CMDQ_EVENT_MUTEX1_STREAM_EOF>;
68 mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x3000 0x1000>,
69 <&gce SUBSYS_1401XXXX 0x2000 0x100>;
73 Example for a client mutex node:
74 mutex: mutex@14020000 {
75 compatible = "mediatek,mt8173-disp-mutex";
76 reg = <0 0x14020000 0 0x1000>;
77 interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_LOW>;
78 power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
79 clocks = <&mmsys CLK_MM_MUTEX_32K>;
80 mediatek,gce-events = <CMDQ_EVENT_MUTEX0_STREAM_EOF>,
81 <CMDQ_EVENT_MUTEX1_STREAM_EOF>;