1 FPGA Region Device Tree Binding
10 - Supported Use Models
11 - Device Tree Examples
18 FPGA Regions represent FPGA's and partial reconfiguration regions of FPGA's in
19 the Device Tree. FPGA Regions provide a way to program FPGAs under device tree
22 This device tree binding document hits some of the high points of FPGA usage and
23 attempts to include terminology used by both major FPGA manufacturers. This
24 document isn't a replacement for any manufacturers specifications for FPGA
32 * The entire FPGA is programmed.
34 Partial Reconfiguration (PR)
35 * A section of an FPGA is reprogrammed while the rest of the FPGA is not
37 * Not all FPGA's support PR.
39 Partial Reconfiguration Region (PRR)
40 * Also called a "reconfigurable partition"
41 * A PRR is a specific section of an FPGA reserved for reconfiguration.
42 * A base (or static) FPGA image may create a set of PRR's that later may
43 be independently reprogrammed many times.
44 * The size and specific location of each PRR is fixed.
45 * The connections at the edge of each PRR are fixed. The image that is loaded
46 into a PRR must fit and must use a subset of the region's connections.
47 * The busses within the FPGA are split such that each region gets its own
48 branch that may be gated independently.
51 * Also called a "partial bit stream"
52 * An FPGA image that is designed to be loaded into a PRR. There may be
53 any number of personas designed to fit into a PRR, but only one at at time
55 * A persona may create more regions.
58 * FPGA Bridges gate bus signals between a host and FPGA.
59 * FPGA Bridges should be disabled while the FPGA is being programmed to
60 prevent spurious signals on the cpu bus and to the soft logic.
61 * FPGA bridges may be actual hardware or soft logic on an FPGA.
62 * During Full Reconfiguration, hardware bridges between the host and FPGA
64 * During Partial Reconfiguration of a specific region, that region's bridge
65 will be used to gate the busses. Traffic to other regions is not affected.
66 * In some implementations, the FPGA Manager transparantly handles gating the
67 buses, eliminating the need to show the hardware FPGA bridges in the
69 * An FPGA image may create a set of reprogrammable regions, each having its
70 own bridge and its own split of the busses in the FPGA.
73 * An FPGA Manager is a hardware block that programs an FPGA under the control
77 * Also called the "static image"
78 * An FPGA image that is designed to do full reconfiguration of the FPGA.
79 * A base image may set up a set of partial reconfiguration regions that may
80 later be reprogrammed.
82 ---------------- ----------------------------------
85 | ----| | ----------- -------- |
86 | | H | | |==>| Bridge0 |<==>| PRR0 | |
87 | | W | | | ----------- -------- |
89 | | B |<=====>|<==| ----------- -------- |
90 | | R | | |==>| Bridge1 |<==>| PRR1 | |
91 | | I | | | ----------- -------- |
93 | | G | | | ----------- -------- |
94 | | E | | |==>| Bridge2 |<==>| PRR2 | |
95 | ----| | ----------- -------- |
97 ---------------- ----------------------------------
99 Figure 1: An FPGA set up with a base image that created three regions. Each
100 region (PRR0-2) gets its own split of the busses that is independently gated by
101 a soft logic bridge (Bridge0-2) in the FPGA. The contents of each PRR can be
102 reprogrammed independently while the rest of the system continues to function.
108 When a DT overlay that targets an FPGA Region is applied, the FPGA Region will
111 1. Disable appropriate FPGA bridges.
112 2. Program the FPGA using the FPGA manager.
113 3. Enable the FPGA bridges.
114 4. The Device Tree overlay is accepted into the live tree.
115 5. Child devices are populated.
117 When the overlay is removed, the child nodes will be removed and the FPGA Region
118 will disable the bridges.
124 FPGA Regions represent FPGA's and FPGA PR regions in the device tree. An FPGA
125 Region brings together the elements needed to program on a running system and
126 add the child devices:
130 * image-specific information needed to to the programming.
133 The intended use is that a Device Tree overlay (DTO) can be used to reprogram an
134 FPGA while an operating system is running.
136 An FPGA Region that exists in the live Device Tree reflects the current state.
137 If the live tree shows a "firmware-name" property or child nodes under an FPGA
138 Region, the FPGA already has been programmed. A DTO that targets an FPGA Region
139 and adds the "firmware-name" property is taken as a request to reprogram the
140 FPGA. After reprogramming is successful, the overlay is accepted into the live
143 The base FPGA Region in the device tree represents the FPGA and supports full
144 reconfiguration. It must include a phandle to an FPGA Manager. The base
145 FPGA region will be the child of one of the hardware bridges (the bridge that
146 allows register access) between the cpu and the FPGA. If there are more than
147 one bridge to control during FPGA programming, the region will also contain a
148 list of phandles to the additional hardware FPGA Bridges.
150 For partial reconfiguration (PR), each PR region will have an FPGA Region.
151 These FPGA regions are children of FPGA bridges which are then children of the
152 base FPGA region. The "Full Reconfiguration to add PRR's" example below shows
155 If an FPGA Region does not specify an FPGA Manager, it will inherit the FPGA
156 Manager specified by its ancestor FPGA Region. This supports both the case
157 where the same FPGA Manager is used for all of an FPGA as well the case where
158 a different FPGA Manager is used for each region.
160 FPGA Regions do not inherit their ancestor FPGA regions' bridges. This prevents
161 shutting down bridges that are upstream from the other active regions while one
162 region is getting reconfigured (see Figure 1 above). During PR, the FPGA's
163 hardware bridges remain enabled. The PR regions' bridges will be FPGA bridges
164 within the static image of the FPGA.
167 - compatible : should contain "fpga-region"
168 - fpga-mgr : should contain a phandle to an FPGA Manager. Child FPGA Regions
169 inherit this property from their ancestor regions. An fpga-mgr property
170 in a region will override any inherited FPGA manager.
171 - #address-cells, #size-cells, ranges : must be present to handle address space
172 mapping for child nodes.
175 - firmware-name : should contain the name of an FPGA image file located on the
176 firmware search path. If this property shows up in a live device tree
177 it indicates that the FPGA has already been programmed with this image.
178 If this property is in an overlay targeting an FPGA region, it is a
179 request to program the FPGA with that image.
180 - fpga-bridges : should contain a list of phandles to FPGA Bridges that must be
181 controlled during FPGA programming along with the parent FPGA bridge.
182 This property is optional if the FPGA Manager handles the bridges.
183 If the fpga-region is the child of an fpga-bridge, the list should not
184 contain the parent bridge.
185 - partial-fpga-config : boolean, set if partial reconfiguration is to be done,
186 otherwise full reconfiguration is done.
187 - external-fpga-config : boolean, set if the FPGA has already been configured
189 - encrypted-fpga-config : boolean, set if the bitstream is encrypted
190 - region-unfreeze-timeout-us : The maximum time in microseconds to wait for
191 bridges to successfully become enabled after the region has been
193 - region-freeze-timeout-us : The maximum time in microseconds to wait for
194 bridges to successfully become disabled before the region has been
196 - config-complete-timeout-us : The maximum time in microseconds time for the
197 FPGA to go to operating mode after the region has been programmed.
198 - child nodes : devices in the FPGA after programming.
200 In the example below, when an overlay is applied targeting fpga-region0,
201 fpga_mgr is used to program the FPGA. Two bridges are controlled during
202 programming: the parent fpga_bridge0 and fpga_bridge1. Because the region is
203 the child of fpga_bridge0, only fpga_bridge1 needs to be specified in the
204 fpga-bridges property. During programming, these bridges are disabled, the
205 firmware specified in the overlay is loaded to the FPGA using the FPGA manager
206 specified in the region. If FPGA programming succeeds, the bridges are
207 reenabled and the overlay makes it into the live device tree. The child devices
208 are then populated. If FPGA programming fails, the bridges are left disabled
209 and the overlay is rejected. The overlay's ranges property maps the lwhps
210 bridge's region (0xff200000) and the hps bridge's region (0xc0000000) for use by
211 the two child devices.
216 fpga_mgr: fpga-mgr@ff706000 {
217 compatible = "altr,socfpga-fpga-mgr";
218 reg = <0xff706000 0x1000
220 interrupts = <0 175 4>;
223 fpga_bridge0: fpga-bridge@ff400000 {
224 compatible = "altr,socfpga-lwhps2fpga-bridge";
225 reg = <0xff400000 0x100000>;
226 resets = <&rst LWHPS2FPGA_RESET>;
227 clocks = <&l4_main_clk>;
229 #address-cells = <1>;
233 fpga_region0: fpga-region0 {
234 compatible = "fpga-region";
235 fpga-mgr = <&fpga_mgr>;
239 fpga_bridge1: fpga-bridge@ff500000 {
240 compatible = "altr,socfpga-hps2fpga-bridge";
241 reg = <0xff500000 0x10000>;
242 resets = <&rst HPS2FPGA_RESET>;
243 clocks = <&l4_main_clk>;
252 #address-cells = <1>;
255 firmware-name = "soc_system.rbf";
256 fpga-bridges = <&fpga_bridge1>;
257 ranges = <0x20000 0xff200000 0x100000>,
258 <0x0 0xc0000000 0x20000000>;
261 compatible = "altr,pio-1.0";
262 reg = <0x10040 0x20>;
270 device_type = "memory";
271 compatible = "altr,onchipmem-15.1";
280 In all cases the live DT must have the FPGA Manager, FPGA Bridges (if any), and
281 a FPGA Region. The target of the Device Tree Overlay is the FPGA Region. Some
282 uses are specific to an FPGA device.
285 In this case, the FPGA Manager which programs the FPGA also handles the
286 bridges behind the scenes. No FPGA Bridge devices are needed for full
289 * Full reconfiguration with hardware bridges
290 In this case, there are hardware bridges between the processor and FPGA that
291 need to be controlled during full reconfiguration. Before the overlay is
292 applied, the live DT must include the FPGA Manager, FPGA Bridges, and a
293 FPGA Region. The FPGA Region is the child of the bridge that allows
294 register access to the FPGA. Additional bridges may be listed in a
295 fpga-bridges property in the FPGA region or in the device tree overlay.
297 * Partial reconfiguration with bridges in the FPGA
298 In this case, the FPGA will have one or more PRR's that may be programmed
299 separately while the rest of the FPGA can remain active. To manage this,
300 bridges need to exist in the FPGA that can gate the buses going to each FPGA
301 region while the buses are enabled for other sections. Before any partial
302 reconfiguration can be done, a base FPGA image must be loaded which includes
303 PRR's with FPGA bridges. The device tree should have an FPGA region for each
309 The intention of this section is to give some simple examples, focusing on
310 the placement of the elements detailed above, especially:
315 * target-path or target
317 For the purposes of this section, I'm dividing the Device Tree into two parts,
318 each with its own requirements. The two parts are:
319 * The live DT prior to the overlay being added
322 The live Device Tree must contain an FPGA Region, an FPGA Manager, and any FPGA
323 Bridges. The FPGA Region's "fpga-mgr" property specifies the manager by phandle
324 to handle programming the FPGA. If the FPGA Region is the child of another FPGA
325 Region, the parent's FPGA Manager is used. If FPGA Bridges need to be involved,
326 they are specified in the FPGA Region by the "fpga-bridges" property. During
327 FPGA programming, the FPGA Region will disable the bridges that are in its
328 "fpga-bridges" list and will re-enable them after FPGA programming has
331 The Device Tree Overlay will contain:
332 * "target-path" or "target"
333 The insertion point where the the contents of the overlay will go into the
334 live tree. target-path is a full path, while target is a phandle.
336 The address space mapping from processor to FPGA bus(ses).
338 Specifies the name of the FPGA image file on the firmware search
339 path. The search path is described in the firmware class documentation.
340 * "partial-fpga-config"
341 This binding is a boolean and should be present if partial reconfiguration
343 * child nodes corresponding to hardware that will be loaded in this region of
346 Device Tree Example: Full Reconfiguration without Bridges
347 =========================================================
349 Live Device Tree contains:
350 fpga_mgr0: fpga-mgr@f8007000 {
351 compatible = "xlnx,zynq-devcfg-1.0";
352 reg = <0xf8007000 0x100>;
353 interrupt-parent = <&intc>;
354 interrupts = <0 8 4>;
356 clock-names = "ref_clk";
360 fpga_region0: fpga-region0 {
361 compatible = "fpga-region";
362 fpga-mgr = <&fpga_mgr0>;
363 #address-cells = <0x1>;
374 #address-cells = <1>;
377 firmware-name = "zynq-gpio.bin";
379 gpio1: gpio@40000000 {
380 compatible = "xlnx,xps-gpio-1.00.a";
381 reg = <0x40000000 0x10000>;
384 xlnx,gpio-width= <0x6>;
388 Device Tree Example: Full Reconfiguration to add PRR's
389 ======================================================
391 The base FPGA Region is specified similar to the first example above.
393 This example programs the FPGA to have two regions that can later be partially
394 configured. Each region has its own bridge in the FPGA fabric.
402 #address-cells = <1>;
405 firmware-name = "base.rbf";
408 compatible = "altr,freeze-bridge-controller";
411 fpga_region1: fpga-region1 {
412 compatible = "fpga-region";
413 #address-cells = <0x1>;
420 compatible = "altr,freeze-bridge-controller";
423 fpga_region2: fpga-region2 {
424 compatible = "fpga-region";
425 #address-cells = <0x1>;
432 Device Tree Example: Partial Reconfiguration
433 ============================================
435 This example reprograms one of the PRR's set up in the previous example.
437 The sequence that occurs when this overlay is similar to the above, the only
438 differences are that the FPGA is partially reconfigured due to the
439 "partial-fpga-config" boolean and the only bridge that is controlled during
440 programming is the FPGA based bridge of fpga_region1.
446 #address-cells = <1>;
449 firmware-name = "soc_image2.rbf";
453 compatible = "altr,pio-1.0";
454 reg = <0x10040 0x20>;
465 It is beyond the scope of this document to fully describe all the FPGA design
466 constraints required to make partial reconfiguration work[1] [2] [3], but a few
467 deserve quick mention.
469 A persona must have boundary connections that line up with those of the partion
470 or region it is designed to go into.
472 During programming, transactions through those connections must be stopped and
473 the connections must be held at a fixed logic level. This can be achieved by
474 FPGA Bridges that exist on the FPGA fabric prior to the partial reconfiguration.
477 [1] www.altera.com/content/dam/altera-www/global/en_US/pdfs/literature/ug/ug_partrecon.pdf
478 [2] tspace.library.utoronto.ca/bitstream/1807/67932/1/Byma_Stuart_A_201411_MAS_thesis.pdf
479 [3] https://www.xilinx.com/support/documentation/sw_manuals/xilinx14_1/ug702.pdf