From 210fd7929306c111818c5202b10b128ae52309c6 Mon Sep 17 00:00:00 2001 From: Christian Lamparter Date: Fri, 5 Feb 2021 11:38:29 +0100 Subject: [PATCH] carl9170 firmware: refresh ch9.h This patch refreshes the upstream linux ch9.h header definitions. Signed-off-by: Christian Lamparter --- include/linux/ch9.h | 450 ++++++++++++++++++++++++++++++++++++++++++-- 1 file changed, 439 insertions(+), 11 deletions(-) diff --git a/include/linux/ch9.h b/include/linux/ch9.h index 94e01bb..e10f879 100644 --- a/include/linux/ch9.h +++ b/include/linux/ch9.h @@ -1,3 +1,4 @@ +/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */ /* * This file holds USB constants and structures that are needed for * USB device APIs. These are used by the USB device model, which is @@ -45,9 +46,9 @@ * This bit flag is used in endpoint descriptors' bEndpointAddress field. * It's also one of three fields in control requests bRequestType. */ -#define USB_DIR_MASK 0x80 #define USB_DIR_OUT 0 /* to device */ #define USB_DIR_IN 0x80 /* to host */ +#define USB_DIR_MASK 0x80 /* * USB types, the second of three bRequestType fields @@ -88,6 +89,8 @@ #define USB_REQ_GET_INTERFACE 0x0A #define USB_REQ_SET_INTERFACE 0x0B #define USB_REQ_SYNCH_FRAME 0x0C +#define USB_REQ_SET_SEL 0x30 +#define USB_REQ_SET_ISOCH_DELAY 0x31 #define USB_REQ_SET_ENCRYPTION 0x0D /* Wireless USB */ #define USB_REQ_GET_ENCRYPTION 0x0E @@ -103,6 +106,13 @@ #define USB_REQ_LOOPBACK_DATA_READ 0x16 #define USB_REQ_SET_INTERFACE_DS 0x17 +/* specific requests for USB Power Delivery */ +#define USB_REQ_GET_PARTNER_PDO 20 +#define USB_REQ_GET_BATTERY_STATUS 21 +#define USB_REQ_SET_PDO 22 +#define USB_REQ_GET_VDM 23 +#define USB_REQ_SEND_VDM 24 + /* The Link Power Management (LPM) ECN defines USB_REQ_TEST_AND_SET command, * used by hubs to put ports into a new L1 suspend state, except that it * forgot to define its number ... @@ -124,8 +134,64 @@ #define USB_DEVICE_A_ALT_HNP_SUPPORT 5 /* (otg) other RH port does */ #define USB_DEVICE_DEBUG_MODE 6 /* (special devices only) */ +/* + * Test Mode Selectors + * See USB 2.0 spec Table 9-7 + */ +#define USB_TEST_J 1 +#define USB_TEST_K 2 +#define USB_TEST_SE0_NAK 3 +#define USB_TEST_PACKET 4 +#define USB_TEST_FORCE_ENABLE 5 + +/* Status Type */ +#define USB_STATUS_TYPE_STANDARD 0 +#define USB_STATUS_TYPE_PTM 1 + +/* + * New Feature Selectors as added by USB 3.0 + * See USB 3.0 spec Table 9-7 + */ +#define USB_DEVICE_U1_ENABLE 48 /* dev may initiate U1 transition */ +#define USB_DEVICE_U2_ENABLE 49 /* dev may initiate U2 transition */ +#define USB_DEVICE_LTM_ENABLE 50 /* dev may send LTM */ +#define USB_INTRF_FUNC_SUSPEND 0 /* function suspend */ + +#define USB_INTR_FUNC_SUSPEND_OPT_MASK 0xFF00 +/* + * Suspend Options, Table 9-8 USB 3.0 spec + */ +#define USB_INTRF_FUNC_SUSPEND_LP (1 << (8 + 0)) +#define USB_INTRF_FUNC_SUSPEND_RW (1 << (8 + 1)) + +/* + * Interface status, Figure 9-5 USB 3.0 spec + */ +#define USB_INTRF_STAT_FUNC_RW_CAP 1 +#define USB_INTRF_STAT_FUNC_RW 2 + #define USB_ENDPOINT_HALT 0 /* IN/OUT will STALL */ +/* Bit array elements as returned by the USB_REQ_GET_STATUS request. */ +#define USB_DEV_STAT_U1_ENABLED 2 /* transition into U1 state */ +#define USB_DEV_STAT_U2_ENABLED 3 /* transition into U2 state */ +#define USB_DEV_STAT_LTM_ENABLED 4 /* Latency tolerance messages */ + +/* + * Feature selectors from Table 9-8 USB Power Delivery spec + */ +#define USB_DEVICE_BATTERY_WAKE_MASK 40 +#define USB_DEVICE_OS_IS_PD_AWARE 41 +#define USB_DEVICE_POLICY_MODE 42 +#define USB_PORT_PR_SWAP 43 +#define USB_PORT_GOTO_MIN 44 +#define USB_PORT_RETURN_POWER 45 +#define USB_PORT_ACCEPT_PD_REQUEST 46 +#define USB_PORT_REJECT_PD_REQUEST 47 +#define USB_PORT_PORT_PD_RESET 48 +#define USB_PORT_C_PORT_PD_CHANGE 49 +#define USB_PORT_CABLE_PD_RESET 50 +#define USB_DEVICE_CHARGING_POLICY 54 /** * struct usb_ctrlrequest - SETUP data for a USB device control request @@ -163,7 +229,8 @@ struct usb_ctrlrequest { * through the Linux-USB APIs, they are not converted to cpu byte * order; it is the responsibility of the client code to do this. * The single exception is when device and configuration descriptors (but - * not other descriptors) are read from usbfs (i.e. /proc/bus/usb/BBB/DDD); + * not other descriptors) are read from character devices + * (i.e. /dev/bus/usb/BBB/DDD); * in this case the fields are converted to host endianness by the kernel. */ @@ -192,8 +259,12 @@ struct usb_ctrlrequest { #define USB_DT_WIRE_ADAPTER 0x21 #define USB_DT_RPIPE 0x22 #define USB_DT_CS_RADIO_CONTROL 0x23 +/* From the T10 UAS specification */ +#define USB_DT_PIPE_USAGE 0x24 /* From the USB 3.0 spec */ #define USB_DT_SS_ENDPOINT_COMP 0x30 +/* From the USB 3.1 spec */ +#define USB_DT_SSP_ISOC_ENDPOINT_COMP 0x31 /* Conventional codes for class-specific descriptors. The convention is * defined in the USB "Common Class" Spec (3.11). Individual class specs @@ -255,6 +326,10 @@ struct usb_device_descriptor { #define USB_CLASS_CONTENT_SEC 0x0d /* content security */ #define USB_CLASS_VIDEO 0x0e #define USB_CLASS_WIRELESS_CONTROLLER 0xe0 +#define USB_CLASS_PERSONAL_HEALTHCARE 0x0f +#define USB_CLASS_AUDIO_VIDEO 0x10 +#define USB_CLASS_BILLBOARD 0x11 +#define USB_CLASS_USB_TYPE_C_BRIDGE 0x12 #define USB_CLASS_MISC 0xef #define USB_CLASS_APP_SPEC 0xfe #define USB_CLASS_VENDOR_SPEC 0xff @@ -293,6 +368,9 @@ struct usb_config_descriptor { /*-------------------------------------------------------------------------*/ +/* USB String descriptors can contain at most 126 characters. */ +#define USB_MAX_STRING_LEN 126 + /* USB_DT_STRING: String descriptor */ struct usb_string_descriptor { __u8 bLength; @@ -346,12 +424,6 @@ struct usb_endpoint_descriptor { #define USB_ENDPOINT_NUMBER_MASK 0x0f /* in bEndpointAddress */ #define USB_ENDPOINT_DIR_MASK 0x80 -#define USB_ENDPOINT_SYNCTYPE 0x0c -#define USB_ENDPOINT_SYNC_NONE (0 << 2) -#define USB_ENDPOINT_SYNC_ASYNC (1 << 2) -#define USB_ENDPOINT_SYNC_ADAPTIVE (2 << 2) -#define USB_ENDPOINT_SYNC_SYNC (3 << 2) - #define USB_ENDPOINT_XFERTYPE_MASK 0x03 /* in bmAttributes */ #define USB_ENDPOINT_XFER_CONTROL 0 #define USB_ENDPOINT_XFER_ISOC 1 @@ -359,6 +431,28 @@ struct usb_endpoint_descriptor { #define USB_ENDPOINT_XFER_INT 3 #define USB_ENDPOINT_MAX_ADJUSTABLE 0x80 +#define USB_ENDPOINT_MAXP_MASK 0x07ff +#define USB_EP_MAXP_MULT_SHIFT 11 +#define USB_EP_MAXP_MULT_MASK (3 << USB_EP_MAXP_MULT_SHIFT) +#define USB_EP_MAXP_MULT(m) \ + (((m) & USB_EP_MAXP_MULT_MASK) >> USB_EP_MAXP_MULT_SHIFT) + +/* The USB 3.0 spec redefines bits 5:4 of bmAttributes as interrupt ep type. */ +#define USB_ENDPOINT_INTRTYPE 0x30 +#define USB_ENDPOINT_INTR_PERIODIC (0 << 4) +#define USB_ENDPOINT_INTR_NOTIFICATION (1 << 4) + +#define USB_ENDPOINT_SYNCTYPE 0x0c +#define USB_ENDPOINT_SYNC_NONE (0 << 2) +#define USB_ENDPOINT_SYNC_ASYNC (1 << 2) +#define USB_ENDPOINT_SYNC_ADAPTIVE (2 << 2) +#define USB_ENDPOINT_SYNC_SYNC (3 << 2) + +#define USB_ENDPOINT_USAGE_MASK 0x30 +#define USB_ENDPOINT_USAGE_DATA 0x00 +#define USB_ENDPOINT_USAGE_FEEDBACK 0x10 +#define USB_ENDPOINT_USAGE_IMPLICIT_FB 0x20 /* Implicit feedback Data endpoint */ + /*-------------------------------------------------------------------------*/ /** @@ -457,8 +551,8 @@ static inline int usb_endpoint_xfer_int( static inline int usb_endpoint_xfer_isoc( const struct usb_endpoint_descriptor *epd) { - return (epd->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) == - USB_ENDPOINT_XFER_ISOC; + return ((epd->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) == + USB_ENDPOINT_XFER_ISOC); } /** @@ -539,6 +633,51 @@ static inline int usb_endpoint_is_isoc_out( return usb_endpoint_xfer_isoc(epd) && usb_endpoint_dir_out(epd); } +/** + * usb_endpoint_maxp - get endpoint's max packet size + * @epd: endpoint to be checked + * + * Returns @epd's max packet bits [10:0] + */ +static inline int usb_endpoint_maxp(const struct usb_endpoint_descriptor *epd) +{ + return le16_to_cpu(epd->wMaxPacketSize) & USB_ENDPOINT_MAXP_MASK; +} + +/** + * usb_endpoint_maxp_mult - get endpoint's transactional opportunities + * @epd: endpoint to be checked + * + * Return @epd's wMaxPacketSize[12:11] + 1 + */ +static inline int +usb_endpoint_maxp_mult(const struct usb_endpoint_descriptor *epd) +{ + int maxp = le16_to_cpu(epd->wMaxPacketSize); + + return USB_EP_MAXP_MULT(maxp) + 1; +} + +static inline int usb_endpoint_interrupt_type( + const struct usb_endpoint_descriptor *epd) +{ + return epd->bmAttributes & USB_ENDPOINT_INTRTYPE; +} + +/*-------------------------------------------------------------------------*/ + +/* USB_DT_SSP_ISOC_ENDPOINT_COMP: SuperSpeedPlus Isochronous Endpoint Companion + * descriptor + */ +struct usb_ssp_isoc_ep_comp_descriptor { + __u8 bLength; + __u8 bDescriptorType; + __le16 wReseved; + __le32 dwBytesPerInterval; +} __attribute__ ((packed)); + +#define USB_DT_SSP_ISOC_EP_COMP_SIZE 8 + /*-------------------------------------------------------------------------*/ /* USB_DT_SS_ENDPOINT_COMP: SuperSpeed Endpoint Companion descriptor */ @@ -553,6 +692,30 @@ struct usb_ss_ep_comp_descriptor { #define USB_DT_SS_EP_COMP_SIZE 6 +/* Bits 4:0 of bmAttributes if this is a bulk endpoint */ +static inline int +usb_ss_max_streams(const struct usb_ss_ep_comp_descriptor *comp) +{ + int max_streams; + + if (!comp) + return 0; + + max_streams = comp->bmAttributes & 0x1f; + + if (!max_streams) + return 0; + + max_streams = 1 << max_streams; + + return max_streams; +} + +/* Bits 1:0 of bmAttributes if this is an isoc endpoint */ +#define USB_SS_MULT(p) (1 + ((p) & 0x3)) +/* Bit 7 of bmAttributes if a SSP isoc endpoint companion descriptor exists */ +#define USB_SS_SSP_ISOC_COMP(p) ((p) & (1 << 7)) + /*-------------------------------------------------------------------------*/ /* USB_DT_DEVICE_QUALIFIER: Device Qualifier descriptor */ @@ -580,10 +743,23 @@ struct usb_otg_descriptor { __u8 bmAttributes; /* support for HNP, SRP, etc */ } __attribute__ ((packed)); +/* USB_DT_OTG (from OTG 2.0 supplement) */ +struct usb_otg20_descriptor { + __u8 bLength; + __u8 bDescriptorType; + + __u8 bmAttributes; /* support for HNP, SRP and ADP, etc */ + __le16 bcdOTG; /* OTG and EH supplement release number + * in binary-coded decimal(i.e. 2.0 is 0200H) + */ +} __attribute__ ((packed)); + /* from usb_otg_descriptor.bmAttributes */ #define USB_OTG_SRP (1 << 0) #define USB_OTG_HNP (1 << 1) /* swap host/device roles */ +#define USB_OTG_ADP (1 << 2) /* support ADP */ +#define OTG_STS_SELECTOR 0xF000 /* OTG status selector */ /*-------------------------------------------------------------------------*/ /* USB_DT_DEBUG: for special highspeed devices, replacing serial console */ @@ -611,6 +787,7 @@ struct usb_interface_assoc_descriptor { __u8 iFunction; } __attribute__ ((packed)); +#define USB_DT_INTERFACE_ASSOCIATION_SIZE 8 /*-------------------------------------------------------------------------*/ @@ -667,6 +844,7 @@ struct usb_bos_descriptor { __u8 bNumDeviceCaps; } __attribute__((packed)); +#define USB_DT_BOS_SIZE 5 /*-------------------------------------------------------------------------*/ /* USB_DT_DEVICE_CAPABILITY: grouped with BOS */ @@ -704,16 +882,209 @@ struct usb_wireless_cap_descriptor { /* Ultra Wide Band */ __u8 bReserved; } __attribute__((packed)); +#define USB_DT_USB_WIRELESS_CAP_SIZE 11 + +/* USB 2.0 Extension descriptor */ #define USB_CAP_TYPE_EXT 2 struct usb_ext_cap_descriptor { /* Link Power Management */ __u8 bLength; __u8 bDescriptorType; __u8 bDevCapabilityType; - __u8 bmAttributes; + __le32 bmAttributes; #define USB_LPM_SUPPORT (1 << 1) /* supports LPM */ +#define USB_BESL_SUPPORT (1 << 2) /* supports BESL */ +#define USB_BESL_BASELINE_VALID (1 << 3) /* Baseline BESL valid*/ +#define USB_BESL_DEEP_VALID (1 << 4) /* Deep BESL valid */ +#define USB_SET_BESL_BASELINE(p) (((p) & 0xf) << 8) +#define USB_SET_BESL_DEEP(p) (((p) & 0xf) << 12) +#define USB_GET_BESL_BASELINE(p) (((p) & (0xf << 8)) >> 8) +#define USB_GET_BESL_DEEP(p) (((p) & (0xf << 12)) >> 12) +} __attribute__((packed)); + +#define USB_DT_USB_EXT_CAP_SIZE 7 + +/* + * SuperSpeed USB Capability descriptor: Defines the set of SuperSpeed USB + * specific device level capabilities + */ +#define USB_SS_CAP_TYPE 3 +struct usb_ss_cap_descriptor { /* Link Power Management */ + __u8 bLength; + __u8 bDescriptorType; + __u8 bDevCapabilityType; + __u8 bmAttributes; +#define USB_LTM_SUPPORT (1 << 1) /* supports LTM */ + __le16 wSpeedSupported; +#define USB_LOW_SPEED_OPERATION (1) /* Low speed operation */ +#define USB_FULL_SPEED_OPERATION (1 << 1) /* Full speed operation */ +#define USB_HIGH_SPEED_OPERATION (1 << 2) /* High speed operation */ +#define USB_5GBPS_OPERATION (1 << 3) /* Operation at 5Gbps */ + __u8 bFunctionalitySupport; + __u8 bU1devExitLat; + __le16 bU2DevExitLat; +} __attribute__((packed)); + +#define USB_DT_USB_SS_CAP_SIZE 10 + +/* + * Container ID Capability descriptor: Defines the instance unique ID used to + * identify the instance across all operating modes + */ +#define CONTAINER_ID_TYPE 4 +struct usb_ss_container_id_descriptor { + __u8 bLength; + __u8 bDescriptorType; + __u8 bDevCapabilityType; + __u8 bReserved; + __u8 ContainerID[16]; /* 128-bit number */ } __attribute__((packed)); +#define USB_DT_USB_SS_CONTN_ID_SIZE 20 + +/* + * SuperSpeed Plus USB Capability descriptor: Defines the set of + * SuperSpeed Plus USB specific device level capabilities + */ +#define USB_SSP_CAP_TYPE 0xa +struct usb_ssp_cap_descriptor { + __u8 bLength; + __u8 bDescriptorType; + __u8 bDevCapabilityType; + __u8 bReserved; + __le32 bmAttributes; +#define USB_SSP_SUBLINK_SPEED_ATTRIBS (0x1f << 0) /* sublink speed entries */ +#define USB_SSP_SUBLINK_SPEED_IDS (0xf << 5) /* speed ID entries */ + __le16 wFunctionalitySupport; +#define USB_SSP_MIN_SUBLINK_SPEED_ATTRIBUTE_ID (0xf) +#define USB_SSP_MIN_RX_LANE_COUNT (0xf << 8) +#define USB_SSP_MIN_TX_LANE_COUNT (0xf << 12) + __le16 wReserved; + __le32 bmSublinkSpeedAttr[1]; /* list of sublink speed attrib entries */ +#define USB_SSP_SUBLINK_SPEED_SSID (0xf) /* sublink speed ID */ +#define USB_SSP_SUBLINK_SPEED_LSE (0x3 << 4) /* Lanespeed exponent */ +#define USB_SSP_SUBLINK_SPEED_ST (0x3 << 6) /* Sublink type */ +#define USB_SSP_SUBLINK_SPEED_RSVD (0x3f << 8) /* Reserved */ +#define USB_SSP_SUBLINK_SPEED_LP (0x3 << 14) /* Link protocol */ +#define USB_SSP_SUBLINK_SPEED_LSM (0xff << 16) /* Lanespeed mantissa */ +} __attribute__((packed)); + +/* + * USB Power Delivery Capability Descriptor: + * Defines capabilities for PD + */ +/* Defines the various PD Capabilities of this device */ +#define USB_PD_POWER_DELIVERY_CAPABILITY 0x06 +/* Provides information on each battery supported by the device */ +#define USB_PD_BATTERY_INFO_CAPABILITY 0x07 +/* The Consumer characteristics of a Port on the device */ +#define USB_PD_PD_CONSUMER_PORT_CAPABILITY 0x08 +/* The provider characteristics of a Port on the device */ +#define USB_PD_PD_PROVIDER_PORT_CAPABILITY 0x09 + +struct usb_pd_cap_descriptor { + __u8 bLength; + __u8 bDescriptorType; + __u8 bDevCapabilityType; /* set to USB_PD_POWER_DELIVERY_CAPABILITY */ + __u8 bReserved; + __le32 bmAttributes; +#define USB_PD_CAP_BATTERY_CHARGING (1 << 1) /* supports Battery Charging specification */ +#define USB_PD_CAP_USB_PD (1 << 2) /* supports USB Power Delivery specification */ +#define USB_PD_CAP_PROVIDER (1 << 3) /* can provide power */ +#define USB_PD_CAP_CONSUMER (1 << 4) /* can consume power */ +#define USB_PD_CAP_CHARGING_POLICY (1 << 5) /* supports CHARGING_POLICY feature */ +#define USB_PD_CAP_TYPE_C_CURRENT (1 << 6) /* supports power capabilities defined in the USB Type-C Specification */ + +#define USB_PD_CAP_PWR_AC (1 << 8) +#define USB_PD_CAP_PWR_BAT (1 << 9) +#define USB_PD_CAP_PWR_USE_V_BUS (1 << 14) + + __le16 bmProviderPorts; /* Bit zero refers to the UFP of the device */ + __le16 bmConsumerPorts; + __le16 bcdBCVersion; + __le16 bcdPDVersion; + __le16 bcdUSBTypeCVersion; +} __attribute__((packed)); + +struct usb_pd_cap_battery_info_descriptor { + __u8 bLength; + __u8 bDescriptorType; + __u8 bDevCapabilityType; + /* Index of string descriptor shall contain the user friendly name for this battery */ + __u8 iBattery; + /* Index of string descriptor shall contain the Serial Number String for this battery */ + __u8 iSerial; + __u8 iManufacturer; + __u8 bBatteryId; /* uniquely identifies this battery in status Messages */ + __u8 bReserved; + /* + * Shall contain the Battery Charge value above which this + * battery is considered to be fully charged but not necessarily + * “topped off.” + */ + __le32 dwChargedThreshold; /* in mWh */ + /* + * Shall contain the minimum charge level of this battery such + * that above this threshold, a device can be assured of being + * able to power up successfully (see Battery Charging 1.2). + */ + __le32 dwWeakThreshold; /* in mWh */ + __le32 dwBatteryDesignCapacity; /* in mWh */ + __le32 dwBatteryLastFullchargeCapacity; /* in mWh */ +} __attribute__((packed)); + +struct usb_pd_cap_consumer_port_descriptor { + __u8 bLength; + __u8 bDescriptorType; + __u8 bDevCapabilityType; + __u8 bReserved; + __u8 bmCapabilities; +/* port will oerate under: */ +#define USB_PD_CAP_CONSUMER_BC (1 << 0) /* BC */ +#define USB_PD_CAP_CONSUMER_PD (1 << 1) /* PD */ +#define USB_PD_CAP_CONSUMER_TYPE_C (1 << 2) /* USB Type-C Current */ + __le16 wMinVoltage; /* in 50mV units */ + __le16 wMaxVoltage; /* in 50mV units */ + __u16 wReserved; + __le32 dwMaxOperatingPower; /* in 10 mW - operating at steady state */ + __le32 dwMaxPeakPower; /* in 10mW units - operating at peak power */ + __le32 dwMaxPeakPowerTime; /* in 100ms units - duration of peak */ +#define USB_PD_CAP_CONSUMER_UNKNOWN_PEAK_POWER_TIME 0xffff +} __attribute__((packed)); + +struct usb_pd_cap_provider_port_descriptor { + __u8 bLength; + __u8 bDescriptorType; + __u8 bDevCapabilityType; + __u8 bReserved1; + __u8 bmCapabilities; +/* port will oerate under: */ +#define USB_PD_CAP_PROVIDER_BC (1 << 0) /* BC */ +#define USB_PD_CAP_PROVIDER_PD (1 << 1) /* PD */ +#define USB_PD_CAP_PROVIDER_TYPE_C (1 << 2) /* USB Type-C Current */ + __u8 bNumOfPDObjects; + __u8 bReserved2; + __le32 wPowerDataObject[]; +} __attribute__((packed)); + +/* + * Precision time measurement capability descriptor: advertised by devices and + * hubs that support PTM + */ +#define USB_PTM_CAP_TYPE 0xb +struct usb_ptm_cap_descriptor { + __u8 bLength; + __u8 bDescriptorType; + __u8 bDevCapabilityType; +} __attribute__((packed)); + +#define USB_DT_USB_PTM_ID_SIZE 3 +/* + * The size of the descriptor for the Sublink Speed Attribute Count + * (SSAC) specified in bmAttributes[4:0]. SSAC is zero-based + */ +#define USB_DT_USB_SSP_CAP_SIZE(ssac) (12 + (ssac + 1) * 4) + /*-------------------------------------------------------------------------*/ /* USB_DT_WIRELESS_ENDPOINT_COMP: companion descriptor associated with @@ -773,8 +1144,10 @@ enum usb_device_speed { USB_SPEED_HIGH, /* usb 2.0 */ USB_SPEED_WIRELESS, /* wireless (usb 2.5) */ USB_SPEED_SUPER, /* usb 3.0 */ + USB_SPEED_SUPER_PLUS, /* usb 3.1 */ }; + enum usb_device_state { /* NOTATTACHED isn't in the USB spec, and this state acts * the same as ATTACHED ... but it's clearer this way. @@ -800,4 +1173,59 @@ enum usb_device_state { */ }; +enum usb3_link_state { + USB3_LPM_U0 = 0, + USB3_LPM_U1, + USB3_LPM_U2, + USB3_LPM_U3 +}; + +/* + * A U1 timeout of 0x0 means the parent hub will reject any transitions to U1. + * 0xff means the parent hub will accept transitions to U1, but will not + * initiate a transition. + * + * A U1 timeout of 0x1 to 0x7F also causes the hub to initiate a transition to + * U1 after that many microseconds. Timeouts of 0x80 to 0xFE are reserved + * values. + * + * A U2 timeout of 0x0 means the parent hub will reject any transitions to U2. + * 0xff means the parent hub will accept transitions to U2, but will not + * initiate a transition. + * + * A U2 timeout of 0x1 to 0xFE also causes the hub to initiate a transition to + * U2 after N*256 microseconds. Therefore a U2 timeout value of 0x1 means a U2 + * idle timer of 256 microseconds, 0x2 means 512 microseconds, 0xFE means + * 65.024ms. + */ +#define USB3_LPM_DISABLED 0x0 +#define USB3_LPM_U1_MAX_TIMEOUT 0x7F +#define USB3_LPM_U2_MAX_TIMEOUT 0xFE +#define USB3_LPM_DEVICE_INITIATED 0xFF + +struct usb_set_sel_req { + __u8 u1_sel; + __u8 u1_pel; + __le16 u2_sel; + __le16 u2_pel; +} __attribute__ ((packed)); + +/* + * The Set System Exit Latency control transfer provides one byte each for + * U1 SEL and U1 PEL, so the max exit latency is 0xFF. U2 SEL and U2 PEL each + * are two bytes long. + */ +#define USB3_LPM_MAX_U1_SEL_PEL 0xFF +#define USB3_LPM_MAX_U2_SEL_PEL 0xFFFF + +/*-------------------------------------------------------------------------*/ + +/* + * As per USB compliance update, a device that is actively drawing + * more than 100mA from USB must report itself as bus-powered in + * the GetStatus(DEVICE) call. + * https://compliance.usb.org/index.asp?UpdateFile=Electrical&Format=Standard#34 + */ +#define USB_SELF_POWER_VBUS_MAX_DRAW 100 + #endif /* __LINUX_USB_CH9_H */ -- 2.31.1