carl9170 firmware: check virtual interface no. range

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: update API to 1.8.6

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: remove unused dummys

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: Support multiple CAB queues

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: boot-up interrupt

The firmware now generates an interrupt after it booted.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: set AHB clock to 40MHz early on

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: compact pta_init

A small gain can be obtained by caching the temporary
usb control flag modifications and commit the new
setting at the end.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: update API to 1.8.5

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: remove usb transport watchdog

The idea of this watchdog was to check regulary,
whenever the driver was still responding to firmware
requests within a reasonable window. But the concept
is flawed and never received any substantial testing.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: revamp reset code

Getting the reset code to work 100% proved to be
a wild-goose chase. Therefore we'll settle with
an easier solution and let the usb subsystem take
care of the clean-up operation.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: add comment about RX overrun recovery

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: Initialize USB subsystem before the DMA engine

The documentation states that the USB DMA engine control register
(0x1e1108) should be modified when the state engine is idling.
By tuning the initialization order and placing a larger workload
in between, the state machine should now always be in the correct
state.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: downgrade MAC reset error level

Currently, MAC resets are the major cause of sudden death
situations. By downgrading the message to just an
"information" the reset logic in the driver no longer
assumes that a serious, fatal event occured and won't
shutdown prematurely.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: put power management definitions into the correct place

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: fix error code handling

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: update API to 1.8.0

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: integrate firmware descriptors

Merge the USB firmware descriptor into OTAR.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: save a few bytes on the command handler

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: add flag for asynchronous commands

This flag can be used by the application to tell _same_
application that it does not have to wait for the command
response, or it does not need to parse the received
response if the flag is set.

NOTE: The firmware does not care about this flag and
processes any received command in the same way.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: implement command sequence counter

The sequence is useful to detect the loss of a command
response/trap.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: update API to 1.7.3

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: speedup handle_rx

Thanks to the improved rx processing in the driver,
rx overruns should no longer happen that frequently.

Also, The overrun detection might not be triggered
in this code-path at all when the recv wlan queue
has run dry.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: move wlan_dma_bump

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: fix array-out-of-bounds bug

This patch fixes an out-of-bounds access which would occur
if the driver sets queue to 6 or 7. Additionally, the
transmission status report has only reserved 2 bits for
reporting this information.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: allow fallback to non-aggregation xmit

This feature might come handy in future. Because aggregation
does not always work as smoothly as hoped. Furthermore,
the original firmware did something similar.

But be advised that once the aggregation for any particular
frame retry was disabled. It should remain disabled for all
following tries and not be enabled again.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: drop noise reading from channel switch response

The driver manually queries the noise values anyway.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: update API to 1.7.2

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: use sudo to install firmware

Only a root-user can modify the files under /lib/firmware.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: streamline dma_put hot-path

This patch restores the original code-path in dma_put.
It no longer tries to correct the control flags for
all dma transfers.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: rename ^CARL*_MASK$ to ^CARL*$

This synchronizes the usage of _MASK in HW defintions
with ath9k and other Atheros' drivers.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: introduce per-rate ER Protection setting

Previously, the firmware has applied (or rather has stuck)
with the ERP settings of the first rate for all retry rates.
This is now history and the driver can choose between
different ERP settings for each individual retry rate.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: update README

the README should include a list of all necessary
tools and libraries to build the firmware.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: checkpatch fixes

Since the shared headers are meant to be included
into the kernel, they should pass checkpatch.pl
without generating hundreds of WARNINGS.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

carl9170 firmware: import 1.7.0

The carl9170 project aims to provide more than just a
working substitute firmware+driver for Atheros' AR9170
USB solutions.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>