From: Oleksij Rempel Date: Mon, 30 Sep 2013 14:54:14 +0000 (+0200) Subject: usb_api_k2_patch.c: use same style like usb_api_magpie_patch.c X-Git-Tag: 1.4.0~10^2~2^2~3 X-Git-Url: https://jxself.org/git/?a=commitdiff_plain;h=8e19d9fd170738c08d06fdf9c36b5d2e6bd94099;p=open-ath9k-htc-firmware.git usb_api_k2_patch.c: use same style like usb_api_magpie_patch.c Just other comment styles and tabs instead of spaces. Some commented A_PRINFs was removed. Signed-off-by: Oleksij Rempel --- diff --git a/target_firmware/magpie_fw_dev/target/hif/usb_api_k2_patch.c b/target_firmware/magpie_fw_dev/target/hif/usb_api_k2_patch.c index bc6948d..48f5565 100755 --- a/target_firmware/magpie_fw_dev/target/hif/usb_api_k2_patch.c +++ b/target_firmware/magpie_fw_dev/target/hif/usb_api_k2_patch.c @@ -77,301 +77,286 @@ extern USB_FIFO_CONFIG usbFifoConf; void _fw_usb_suspend_reboot() { - volatile uint32_t gpio_in = 0; - volatile uint32_t pupd = 0; - volatile uint32_t t = 0; - volatile uint32_t sof_no=0,sof_no_new=0; - /* Set GO_TO_SUSPEND bit to USB main control register */ - vUsb_suspend(); - A_PRINTF("!USB suspend\n\r"); - - // keep the record of suspend + volatile uint32_t gpio_in = 0; + volatile uint32_t pupd = 0; + volatile uint32_t t = 0; + volatile uint32_t sof_no=0,sof_no_new=0; + /* Set GO_TO_SUSPEND bit to USB main control register */ + vUsb_suspend(); + A_PRINTF("!USB suspend\n\r"); + + /* keep the record of suspend */ #if defined(PROJECT_MAGPIE) - *((volatile uint32_t*)WATCH_DOG_MAGIC_PATTERN_ADDR) = SUS_MAGIC_PATTERN; + *((volatile uint32_t*)WATCH_DOG_MAGIC_PATTERN_ADDR) = SUS_MAGIC_PATTERN; #elif defined(PROJECT_K2) - HAL_WORD_REG_WRITE(MAGPIE_REG_RST_STATUS_ADDR, SUS_MAGIC_PATTERN); + HAL_WORD_REG_WRITE(MAGPIE_REG_RST_STATUS_ADDR, SUS_MAGIC_PATTERN); #endif /* #if defined(PROJECT_MAGPIE) */ - /* Reset USB FIFO */ - A_USB_RESET_FIFO(); + /* Reset USB FIFO */ + A_USB_RESET_FIFO(); - /* Turn off power */ - A_USB_POWER_OFF(); + /* Turn off power */ + A_USB_POWER_OFF(); - DEBUG_SYSTEM_STATE = (DEBUG_SYSTEM_STATE&(~0xffff)) | 0x1000; + DEBUG_SYSTEM_STATE = (DEBUG_SYSTEM_STATE&(~0xffff)) | 0x1000; - // reset ep3/ep4 fifo in case there is data which might affect resuming + /* reset ep3/ep4 fifo in case there + * is data which might affect resuming */ // HAL_BYTE_REG_WRITE(0x100ae, (HAL_BYTE_REG_READ(0x100ae)|0x10)); // HAL_BYTE_REG_WRITE(0x100ae, (HAL_BYTE_REG_READ(0x100af)|0x10)); - { - // config gpio to input before goto suspend - - //disable JTAG/ICE - //jtag = HAL_WORD_REG_READ(0x10004054); - //HAL_WORD_REG_WRITE(0x10004054, (jtag|BIT17)); - - //disable SPI - //spi = HAL_WORD_REG_READ(0x50040); - //HAL_WORD_REG_WRITE(0x50040, (spi&~(BIT8))); - - //set all GPIO to input - gpio_in = HAL_WORD_REG_READ(0x1000404c); - HAL_WORD_REG_WRITE(0x1000404c, 0x0); - - //set PU/PD for all GPIO except two UART pins - pupd = HAL_WORD_REG_READ(0x10004088); - HAL_WORD_REG_WRITE(0x10004088, 0xA982AA6A); - } - - sof_no= HAL_WORD_REG_READ(0x10004); - for (t = 0; t < CHECK_SOF_LOOP_CNT; t++) - { - A_DELAY_USECS(1000); //delay 1ms - sof_no_new = HAL_WORD_REG_READ(0x10004); - - if(sof_no_new == sof_no) - break; - - sof_no = sof_no_new; - } - - /* - * Reset "printf" module patch point(RAM to ROM) when K2 warm start or suspend, - * which fixed the error issue cause by redownload another different firmware. - */ - _indir_tbl.cmnos.printf._printf = save_cmnos_printf; - - /////////////////////////////////////////////////////////////// - // setting the go suspend here, power down right away... - if (t != CHECK_SOF_LOOP_CNT) // not time out - HAL_WORD_REG_WRITE(0x10000, HAL_WORD_REG_READ(0x10000)|(0x8)); - /////////////////////////////////////////////////////////////// - - DEBUG_SYSTEM_STATE = (DEBUG_SYSTEM_STATE&(~0xffff)) | 0x1100; - -#if 0 // pll unstable, h/w bug? - HAL_WORD_REG_WRITE(0x50040, (0x300|6|(1>>1)<<12)); - A_UART_HWINIT((40*1000*1000)/1, 19200); + { + /* config gpio to input before goto suspend */ + + /* disable JTAG/ICE */ + //jtag = HAL_WORD_REG_READ(0x10004054); + //HAL_WORD_REG_WRITE(0x10004054, (jtag|BIT17)); + + /* disable SPI */ + //spi = HAL_WORD_REG_READ(0x50040); + //HAL_WORD_REG_WRITE(0x50040, (spi&~(BIT8))); + + /* set all GPIO to input */ + gpio_in = HAL_WORD_REG_READ(0x1000404c); + HAL_WORD_REG_WRITE(0x1000404c, 0x0); + + /* set PU/PD for all GPIO except two UART pins */ + pupd = HAL_WORD_REG_READ(0x10004088); + HAL_WORD_REG_WRITE(0x10004088, 0xA982AA6A); + } + + sof_no= HAL_WORD_REG_READ(0x10004); + for (t = 0; t < CHECK_SOF_LOOP_CNT; t++) + { + A_DELAY_USECS(1000); /* delay 1ms */ + sof_no_new = HAL_WORD_REG_READ(0x10004); + + if(sof_no_new == sof_no) + break; + sof_no = sof_no_new; + } + + /* + * Reset "printf" module patch point(RAM to ROM) + * when K2 warm start or suspend, + * which fixed the error issue cause by redownload + * another different firmware. + */ + _indir_tbl.cmnos.printf._printf = save_cmnos_printf; + + /* !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! + * setting the go suspend here, power down right away!!! + */ + if (t != CHECK_SOF_LOOP_CNT) /* not time out */ + HAL_WORD_REG_WRITE(0x10000, HAL_WORD_REG_READ(0x10000)|(0x8)); + + DEBUG_SYSTEM_STATE = (DEBUG_SYSTEM_STATE&(~0xffff)) | 0x1100; + +#if 0 /* pll unstable, h/w bug? */ + HAL_WORD_REG_WRITE(0x50040, (0x300|6|(1>>1)<<12)); + A_UART_HWINIT((40*1000*1000)/1, 19200); #endif - { - // restore gpio setting - //HAL_WORD_REG_WRITE(0x10004054, jtag); - //HAL_WORD_REG_WRITE(0x50040, spi); - HAL_WORD_REG_WRITE(0x1000404c, gpio_in); - HAL_WORD_REG_WRITE(0x10004088, pupd); - } - DEBUG_SYSTEM_STATE = (DEBUG_SYSTEM_STATE&(~0xffff)) | 0x1200; - - { - // since we still need to touch mac_base address after resuming back, so that - // reset mac can't be done in ResetFifo function, move to here... - // whole mac control reset.... (bit1) - HAL_WORD_REG_WRITE( MAGPIE_REG_RST_PWDN_CTRL_ADDR, (BIT1) ); - HAL_WORD_REG_WRITE( MAGPIE_REG_RST_PWDN_CTRL_ADDR, (HAL_WORD_REG_READ(MAGPIE_REG_RST_PWDN_CTRL_ADDR)|BIT0)); - HAL_WORD_REG_WRITE( MAGPIE_REG_RST_PWDN_CTRL_ADDR, 0x0 ); + /* restore gpio setting */ + //HAL_WORD_REG_WRITE(0x10004054, jtag); + //HAL_WORD_REG_WRITE(0x50040, spi); + HAL_WORD_REG_WRITE(0x1000404c, gpio_in); + HAL_WORD_REG_WRITE(0x10004088, pupd); + + DEBUG_SYSTEM_STATE = (DEBUG_SYSTEM_STATE&(~0xffff)) | 0x1200; + + /* since we still need to touch mac_base address after resuming back, + * so that reset mac can't be done in ResetFifo function, + * move to here... whole mac control reset.... (bit1) + */ + HAL_WORD_REG_WRITE(MAGPIE_REG_RST_PWDN_CTRL_ADDR, (BIT1)); + HAL_WORD_REG_WRITE(MAGPIE_REG_RST_PWDN_CTRL_ADDR, + (HAL_WORD_REG_READ(MAGPIE_REG_RST_PWDN_CTRL_ADDR)|BIT0)); + HAL_WORD_REG_WRITE(MAGPIE_REG_RST_PWDN_CTRL_ADDR, 0x0); A_DELAY_USECS(1000); - } - //A_PRINTF("reg(0x10020)=(%x)\n", HAL_WORD_REG_READ(0x10020)); - // disable ep3 int enable, so that resume back won't send wdt magic pattern out!!! - mUSB_STATUS_IN_INT_DISABLE(); + //A_PRINTF("reg(0x10020)=(%x)\n", HAL_WORD_REG_READ(0x10020)); + /* disable ep3 int enable, so that resume back won't + * send wdt magic pattern out!!! */ + mUSB_STATUS_IN_INT_DISABLE(); - MAGPIE_REG_USB_RX0_SWAP_DATA = 0x1; - MAGPIE_REG_USB_TX0_SWAP_DATA = 0x1; - MAGPIE_REG_USB_RX1_SWAP_DATA = 0x1; - MAGPIE_REG_USB_RX2_SWAP_DATA = 0x1; + MAGPIE_REG_USB_RX0_SWAP_DATA = 0x1; + MAGPIE_REG_USB_TX0_SWAP_DATA = 0x1; + MAGPIE_REG_USB_RX1_SWAP_DATA = 0x1; + MAGPIE_REG_USB_RX2_SWAP_DATA = 0x1; - if (((DEBUG_SYSTEM_STATE&~(0x0000ffff))>>16 == 0x5342)) { - /* UART_SEL and SPI_SEL */ - HAL_WORD_REG_WRITE(0x50040, (0x300|0|(1>>1)<<12)); - } - - /* Jump to boot code */ - A_USB_JUMP_BOOT(); + if (((DEBUG_SYSTEM_STATE&~(0x0000ffff))>>16 == 0x5342)) { + /* UART_SEL and SPI_SEL */ + HAL_WORD_REG_WRITE(0x50040, (0x300|0|(1>>1)<<12)); + } + /* Jump to boot code */ + A_USB_JUMP_BOOT(); } /* - * -- patch usb_fw_task -- - * . usb zero length interrupt should not clear by s/w, h/w will handle that - * . complete suspend handle, configure gpio, turn off related function, - * slow down the pll for stable issue + * patch usb_fw_task + * usb zero length interrupt should not clear by s/w, h/w will handle that + * complete suspend handle, configure gpio, turn off related function, + * slow down the pll for stable issue */ void _fw_usb_fw_task(void) { - register uint8_t usb_interrupt_level1; - register uint8_t usb_interrupt_level2; - - usb_interrupt_level1 = USB_BYTE_REG_READ(ZM_INTR_GROUP_OFFSET); -#if 0 // these endpoints are handled by DMA - if (usb_interrupt_level1 & BIT5) //Group Byte 5 - { - vUsb_Data_In(); - } + register uint8_t usb_interrupt_level1; + register uint8_t usb_interrupt_level2; + + usb_interrupt_level1 = USB_BYTE_REG_READ(ZM_INTR_GROUP_OFFSET); +#if 0 /* these endpoints are handled by DMA */ + if (usb_interrupt_level1 & BIT5) + { + vUsb_Data_In(); + } #endif - if (usb_interrupt_level1 & BIT4) - { - usb_interrupt_level2 = USB_BYTE_REG_READ(ZM_INTR_SOURCE_4_OFFSET); - if( usb_interrupt_level2 & BIT6) - A_USB_REG_OUT();//vUsb_Reg_Out(); - } - - if (usb_interrupt_level1 & BIT6) - { - //zfGenWatchDogEvent(); - usb_interrupt_level2 = USB_BYTE_REG_READ(ZM_INTR_SOURCE_6_OFFSET); - if( usb_interrupt_level2 & BIT6) - A_USB_STATUS_IN();//vUsb_Status_In(); - } - - if (usb_interrupt_level1 & BIT0) //Group Byte 0 - { - //usb_interrupt_level2 = ZM_INTR_SOURCE_0_REG; - usb_interrupt_level2 = USB_BYTE_REG_READ(ZM_INTR_SOURCE_0_OFFSET); - - // refer to FUSB200, p 48, offset:21H, bit7 description, should clear the command abort interrupt first!? - if (usb_interrupt_level2 & BIT7) - { - //ZM_INTR_SOURCE_0_REG &= 0x7f; // Handle command abort - USB_BYTE_REG_WRITE(ZM_INTR_SOURCE_0_OFFSET, (USB_BYTE_REG_READ(ZM_INTR_SOURCE_0_OFFSET)& ~BIT7)); - A_PRINTF("![SOURCE_0] bit7 on\n\r"); - } - - if (usb_interrupt_level2 & BIT1) - { - //A_PRINTF("![USB] ep0 IN in \n\r"); - A_USB_EP0_TX(); // USB EP0 tx interrupt - } - if (usb_interrupt_level2 & BIT2) - { - //A_PRINTF("![USB] ep0 OUT in\n\r"); - A_USB_EP0_RX(); // USB EP0 rx interrupt - } - if (usb_interrupt_level2 & BIT0) - { - //A_PRINTF("![USB] ep0 SETUP in\n\r"); - A_USB_EP0_SETUP(); - //vWriteUSBFakeData(); - } -// else if (usb_interrupt_level2 & BIT3) - if (usb_interrupt_level2 & BIT3) - { - vUsb_ep0end(); -// A_PRINTF("![SOURCE_0] ep0 CMD_END\n\r"); - } - if (usb_interrupt_level2 & BIT4) - { - vUsb_ep0fail(); -// A_PRINTF("![SOURCE_0] ep0 CMD_FAIL\n\r"); - } - if (eUsbCxFinishAction == ACT_STALL) - { - // set CX_STL to stall Endpoint0 & will also clear FIFO0 - USB_BYTE_REG_WRITE(ZM_CX_CONFIG_STATUS_OFFSET, 0x04); -// A_PRINTF("![USB] ZM_CX_CONFIG_STATUS_REG = 0x04\n\r"); - } - else if (eUsbCxFinishAction == ACT_DONE) - { - // set CX_DONE to indicate the transmistion of control frame - USB_BYTE_REG_WRITE(ZM_CX_CONFIG_STATUS_OFFSET, 0x01); - } - eUsbCxFinishAction = ACT_IDLE; - } - - if (usb_interrupt_level1 & BIT7) //Group Byte 7 - { - //usb_interrupt_level2 = ZM_INTR_SOURCE_7_REG; - usb_interrupt_level2 = USB_BYTE_REG_READ(ZM_INTR_SOURCE_7_OFFSET); + if (usb_interrupt_level1 & BIT4) { + usb_interrupt_level2 = + USB_BYTE_REG_READ(ZM_INTR_SOURCE_4_OFFSET); + + if(usb_interrupt_level2 & BIT6) + A_USB_REG_OUT(); /* vUsb_Reg_Out() */ + } + + if (usb_interrupt_level1 & BIT6) { + /* zfGenWatchDogEvent(); ?? */ + usb_interrupt_level2 = + USB_BYTE_REG_READ(ZM_INTR_SOURCE_6_OFFSET); + if(usb_interrupt_level2 & BIT6) + A_USB_STATUS_IN(); /* vUsb_Status_In() */ + } + + if (usb_interrupt_level1 & BIT0) { + usb_interrupt_level2 = + USB_BYTE_REG_READ(ZM_INTR_SOURCE_0_OFFSET); + + /* refer to FUSB200, p 48, offset:21H, bit7 description, + * should clear the command abort interrupt first!? + */ + if (usb_interrupt_level2 & BIT7) { + /* Handle command abort */ + USB_BYTE_REG_WRITE(ZM_INTR_SOURCE_0_OFFSET, + (USB_BYTE_REG_READ(ZM_INTR_SOURCE_0_OFFSET) + & ~BIT7)); + A_PRINTF("![SOURCE_0] bit7 on\n\r"); + } + + if (usb_interrupt_level2 & BIT1) + A_USB_EP0_TX(); /* USB EP0 tx interrupt */ + + if (usb_interrupt_level2 & BIT2) + A_USB_EP0_RX(); /* USB EP0 rx interrupt */ + + if (usb_interrupt_level2 & BIT0) { + A_USB_EP0_SETUP(); + /* vWriteUSBFakeData() */ + } + + if (usb_interrupt_level2 & BIT3) + vUsb_ep0end(); + + if (usb_interrupt_level2 & BIT4) + vUsb_ep0fail(); + + if (eUsbCxFinishAction == ACT_STALL) { + /* set CX_STL to stall Endpoint0 & + * will also clear FIFO0 */ + USB_BYTE_REG_WRITE(ZM_CX_CONFIG_STATUS_OFFSET, 0x04); + } else if (eUsbCxFinishAction == ACT_DONE) { + /* set CX_DONE to indicate the transmistion + * of control frame */ + USB_BYTE_REG_WRITE(ZM_CX_CONFIG_STATUS_OFFSET, 0x01); + } + eUsbCxFinishAction = ACT_IDLE; + } + + if (usb_interrupt_level1 & BIT7) { + usb_interrupt_level2 = + USB_BYTE_REG_READ(ZM_INTR_SOURCE_7_OFFSET); #if 0 - if (usb_interrupt_level2 & BIT7) - { - vUsb_Data_Out0Byte(); -// A_PRINTF("![SOURCE_7] bit7 on, clear it\n\r"); - } - if (usb_interrupt_level2 & BIT6) - { - vUsb_Data_In0Byte(); -// A_PRINTF("![SOURCE_7] bit6 on, clear it\n\r"); - } + if (usb_interrupt_level2 & BIT7) + vUsb_Data_Out0Byte(); + + if (usb_interrupt_level2 & BIT6) + vUsb_Data_In0Byte(); #endif - - if (usb_interrupt_level2 & BIT1) - { - vUsb_rst(); - //USB_BYTE_REG_WRITE(ZM_INTR_SOURCE_7_REG, (USB_BYTE_REG_READ(ZM_INTR_SOURCE_7_OFFSET)&~0x2)); - A_PRINTF("!USB reset\n\r"); -// A_PRINTF("![0x1012c]: %\n\r", USB_WORD_REG_READ(0x12c)); - } - if (usb_interrupt_level2 & BIT2) - { - // TBD: the suspend resume code should put here, Ryan, 07/18 - // - // issue, jump back to rom code and what peripherals should we reset here? - // - _fw_usb_suspend_reboot(); - } - if (usb_interrupt_level2 & BIT3) - { - vUsb_resm(); - A_PRINTF("!USB resume\n\r"); - } - } + if (usb_interrupt_level2 & BIT1) { + vUsb_rst(); + A_PRINTF("!USB reset\n\r"); +// A_PRINTF("![0x1012c]: %\n\r", USB_WORD_REG_READ(0x12c)); + } + if (usb_interrupt_level2 & BIT2) { + /* TBD: the suspend resume code should put here, + * Ryan, 07/18 + * issue, jump back to rom code and what peripherals + * should we reset here? */ + _fw_usb_suspend_reboot(); + } + if (usb_interrupt_level2 & BIT3) { + vUsb_resm(); + A_PRINTF("!USB resume\n\r"); + } + } } void _fw_usb_reset_fifo(void) { - volatile uint32_t *reg_data; - - HAL_BYTE_REG_WRITE(0x100ae, (HAL_BYTE_REG_READ(0x100ae)|0x10)); - HAL_BYTE_REG_WRITE(0x100af, (HAL_BYTE_REG_READ(0x100af)|0x10)); - - // disable ep3 int enable, so that resume back won't send wdt magic pattern out!!! - mUSB_STATUS_IN_INT_DISABLE(); - - // update magic pattern to indicate this is a suspend - // k2: MAGPIE_REG_RST_WDT_TIMER_CTRL_ADDR - // magpie: MAGPIE_REG_RST_STATUS_ADDR - HAL_WORD_REG_WRITE(MAGPIE_REG_RST_STATUS_ADDR, SUS_MAGIC_PATTERN); - - /* - * Before USB suspend, USB DMA must be reset(refer to Otus) - * Otus runs the following statements only - * HAL_WORD_REG_WRITE( MAGPIE_REG_RST_PWDN_CTRL_ADDR, BIT0|BIT2 ); - * HAL_WORD_REG_WRITE( MAGPIE_REG_RST_PWDN_CTRL_ADDR, 0x0 ); - * K2 must run the following statements additionally - * reg_data = (A_UINT32 *)(USB_CTRL_BASE_ADDRESS + 0x118); - * *reg_data = 0x00000000; - * *reg_data = 0x00000001; - * because of Hardware bug in K2 - */ - reg_data = (uint32_t *)(USB_CTRL_BASE_ADDRESS + 0x118); - *reg_data = 0x00000000; - - // reset both usb(bit2)/wlan(bit1) dma - HAL_WORD_REG_WRITE( MAGPIE_REG_RST_PWDN_CTRL_ADDR, (BIT2) ); - HAL_WORD_REG_WRITE( MAGPIE_REG_RST_PWDN_CTRL_ADDR, (HAL_WORD_REG_READ(MAGPIE_REG_RST_PWDN_CTRL_ADDR)|BIT0)); - HAL_WORD_REG_WRITE( MAGPIE_REG_RST_PWDN_CTRL_ADDR, 0x0 ); - - *reg_data = 0x00000001; - - /* MAC warem reset */ - //reg_data = (uint32_t *)(K2_REG_MAC_BASE_ADDR + 0x7000); - //*reg_data = 0x00000001; - - //A_DELAY_USECS(1); - - //*reg_data = 0x00000000; - - //while (*reg_data) ; - - A_PRINTF("\n change clock to 22 and go to suspend now!"); - - /* UART_SEL */ - HAL_WORD_REG_WRITE(0x50040, (0x200|0|(1>>1)<<12)); - A_UART_HWINIT((22*1000*1000), 19200); + volatile uint32_t *reg_data; + + HAL_BYTE_REG_WRITE(0x100ae, (HAL_BYTE_REG_READ(0x100ae)|0x10)); + HAL_BYTE_REG_WRITE(0x100af, (HAL_BYTE_REG_READ(0x100af)|0x10)); + + /* disable ep3 int enable, so that resume back won't + * send wdt magic pattern out!!! + */ + mUSB_STATUS_IN_INT_DISABLE(); + + /* update magic pattern to indicate this is a suspend + * k2: MAGPIE_REG_RST_WDT_TIMER_CTRL_ADDR + * magpie: MAGPIE_REG_RST_STATUS_ADDR + */ + HAL_WORD_REG_WRITE(MAGPIE_REG_RST_STATUS_ADDR, SUS_MAGIC_PATTERN); + + /* + * Before USB suspend, USB DMA must be reset(refer to Otus) + * Otus runs the following statements only + * HAL_WORD_REG_WRITE( MAGPIE_REG_RST_PWDN_CTRL_ADDR, BIT0|BIT2 ); + * HAL_WORD_REG_WRITE( MAGPIE_REG_RST_PWDN_CTRL_ADDR, 0x0 ); + * K2 must run the following statements additionally + * reg_data = (A_UINT32 *)(USB_CTRL_BASE_ADDRESS + 0x118); + * *reg_data = 0x00000000; + * *reg_data = 0x00000001; + * because of Hardware bug in K2 + */ + reg_data = (uint32_t *)(USB_CTRL_BASE_ADDRESS + 0x118); + *reg_data = 0x00000000; + + /* reset both usb(bit2)/wlan(bit1) dma */ + HAL_WORD_REG_WRITE(MAGPIE_REG_RST_PWDN_CTRL_ADDR, (BIT2)); + HAL_WORD_REG_WRITE(MAGPIE_REG_RST_PWDN_CTRL_ADDR, + (HAL_WORD_REG_READ(MAGPIE_REG_RST_PWDN_CTRL_ADDR)|BIT0)); + HAL_WORD_REG_WRITE(MAGPIE_REG_RST_PWDN_CTRL_ADDR, 0x0); + + *reg_data = 0x00000001; + + /* MAC warem reset */ + //reg_data = (uint32_t *)(K2_REG_MAC_BASE_ADDR + 0x7000); + //*reg_data = 0x00000001; + + //A_DELAY_USECS(1); + + //*reg_data = 0x00000000; + + //while (*reg_data) ; + + A_PRINTF("\n change clock to 22 and go to suspend now!"); + + /* UART_SEL */ + HAL_WORD_REG_WRITE(0x50040, (0x200|0|(1>>1)<<12)); + A_UART_HWINIT((22*1000*1000), 19200); } #endif