X-Git-Url: https://jxself.org/git/?a=blobdiff_plain;f=carlfw%2FKconfig;h=455c793536a326f4746b3fc94a9f2f6b33763123;hb=HEAD;hp=a122f804237d273b9627d2aaa063a82138be5e12;hpb=8bd3397985e442761ce6956b3ba2e126a2577c42;p=carl9170fw.git

diff --git a/carlfw/Kconfig b/carlfw/Kconfig
index a122f80..455c793 100644
--- a/carlfw/Kconfig
+++ b/carlfw/Kconfig
@@ -34,7 +34,7 @@ config CARL9170FW_RX_FRAME_LEN
 config CARL9170FW_GPIO_INTERRUPT
 	def_bool y
 	prompt "GPIO Software Interrupt"
-	---help---
+	help
 	 When this option is enabled, the firmware will poll the GPIO
 	 registers and reports to the driver whenever the GPIO state
 	 has changed from a previous state.
@@ -45,7 +45,7 @@ config CARL9170FW_GPIO_INTERRUPT
 config CARL9170FW_SECURITY_ENGINE
 	def_bool y
 	prompt "Support Hardware Crypto Engine"
-	---help---
+	help
 	 This options controls if the firmware will allow the driver
 	 to program the security engine / CAM through a firmware
 	 interface.
@@ -56,7 +56,7 @@ config CARL9170FW_SECURITY_ENGINE
 config CARL9170FW_RADIO_FUNCTIONS
 	def_bool y
 	prompt "Enable Firmware-supported Radio/RF functions"
-	---help---
+	help
 	 Some PHY/RF functions (e.g.: AGC and Noise calibration) need
 	 to be done in the firmware.
 
@@ -65,21 +65,6 @@ config CARL9170FW_RADIO_FUNCTIONS
 
 endmenu
 
-menu "802.11 Firmware Features"
-
-config CARL9170FW_CAB_QUEUE
-	def_bool y
-	prompt "Support software-based Content after Beacon Queue"
-	---help---
-	 This (software) queue is used to send any broad-/multi-cast buffered
-	 frames after the next DTIM beacon.
-
-	 This feature is required for Accesspoint mode operation.
-
-	 Say Y.
-
-endmenu
-
 source "carlfw/usb/Kconfig"
 
 menu "Experimental, Unstable & Testing Extensions"
@@ -88,7 +73,7 @@ config CARL9170FW_PRINTF
 	def_bool y
 	prompt "Advanced printf"
 	depends on CARL9170FW_DEBUG_UART || CARL9170FW_DEBUG_USB
-	---help---
+	help
 	 Advanced printf (very useful for debugging purposes)
 	 The formats supported by this implementation are:
 		'd' 'u' 'c' 's' 'x' 'X' 'p'.
@@ -104,7 +89,7 @@ config CARL9170FW_WOL_OPTION
 	def_bool n
 	prompt "Wakeup on WLAN"
 	depends on CARL9170FW_EXPERIMENTAL
-	---help---
+	help
 	 With this option enabled, the firmware can wake-up
 	 suspended hosts... As long as they fully support
 	 USB remote wakeup.
@@ -118,7 +103,7 @@ config CARL9170FW_WOL_NL80211_TRIGGERS
 	prompt "Standard NL80211 wakeup triggers"
 	depends on CARL9170FW_WOL_OPTION
 	select CARL9170FW_WOL
-	---help---
+	help
 	 Available triggers:
 	  * Magic Packet(tm) pattern
 	  * disconnect event
@@ -128,7 +113,7 @@ config CARL9170FW_WOL_PROBE_REQUEST
 	prompt "Probe Request"
 	depends on CARL9170FW_WOL_OPTION
 	select CARL9170FW_WOL
-	---help---
+	help
 	 Scan probe requests for a given SSID.
 
 config CARL9170FW_WOL_PROBE_REQUEST_SSID
@@ -153,9 +138,19 @@ config CARL9170FW_NOISY_MAC_RESET
 	prompt "Notify MAC RESET events"
 	depends on CARL9170FW_FW_MAC_RESET
 
+config CARL9170FW_80MHZ_CLOCK
+	def_bool n
+	prompt "Allow 80/88MHz clock for HT40"
+	depends on CARL9170FW_EXPERIMENTAL
+	help
+	 The SoC can run up to 80/88MHz in HT40 mode. This improves
+	 throughput and timing accuracy over the 40/44MHz clock.
+	 However some devices don't have heat shields and they with
+	 this option enabled, they become unstable under load.
+
 config CARL9170FW_BROKEN_FEATURES
 	def_bool n
-	prompt "Broken Featurs"
+	prompt "Broken Features"
 
 config CARL9170FW_DEBUG
 	def_bool n
@@ -166,7 +161,7 @@ config CARL9170FW_DEBUG_LED_HEARTBEAT
 	def_bool n
 	prompt "LED Heartbeat"
 	depends on CARL9170FW_BROKEN_FEATURES
-	---help---
+	help
 	 This option conflicts with the application's LED code.
 	 Also, it assumes that you have two LEDs, which is not
 	 necessarily true.
@@ -175,7 +170,7 @@ config CARL9170FW_DEBUG_UART
 	def_bool n
 	prompt "Pass debug messages through Highspeed UART"
 	depends on CARL9170FW_BROKEN_FEATURES
-	---help---
+	help
 	 This option allows the firmware to send BUG/ERR/INFO/DBG and
 	 hexdumps through the UART _as well_. However, first: you must
 	 connect a working logger.
@@ -198,41 +193,15 @@ config CARL9170FW_UART_CLOCK_40M
 
 endchoice
 
-
-choice
-	prompt "TX / RX Path"
-
-	default CARL9170FW_NORMAL_TX_RX
-
-	config CARL9170FW_NORMAL_TX_RX
-		bool
-		prompt "Normal WLAN TX/RX routines"
-
-	config CARL9170FW_LOOPBACK
-		bool
-		depends on CARL9170FW_BROKEN_FEATURES
-		prompt "TX->(tx feedback)->RX loopback"
-		---help---
-		 Useful carlu testcase.
-
-	config CARL9170FW_DISCARD
-		bool
-		depends on CARL9170FW_BROKEN_FEATURES
-		prompt "TX->(tx feedback)"
-		---help---
-		 Useful carlu testcase
-
-endchoice
-
 config CARL9170FW_UNUSABLE
 	def_bool y
-	depends on CARL9170FW_BROKEN || CARL9170FW_LOOPBACK
+	depends on CARL9170FW_BROKEN || CARL9170FW_DEBUG
 
 config CARL9170FW_USB_MODESWITCH
 	def_bool n
 	prompt "USB 1.1 / 2.0 switching support"
-	depends on CARL9170FW_BROKEN_FEATURES
-	---help---
+	depends on CARL9170FW_BROKEN_FEATURES && CARL9170FW_USB_STANDARD_CMDS
+	help
 	 Mostly implemented, but untested and some serious
 	 doubts remain.
 
@@ -245,7 +214,7 @@ menu "Build Options"
 config CARL9170FW_AGGRESSIVE_CFLAGS
 	def_bool y
 	prompt "Enable aggressive size optimization"
-	---help---
+	help
 	 This option adds several more optimization compiler flags,
 	 which can greatly reduce the firmware size... at the expense
 	 of machine-code readability.