endmenu
-menu "802.11 Firmware Features"
-
-config CARL9170FW_CAB_QUEUE
- def_bool y
- prompt "Support software-based Content after Beacon Queue"
- ---help---
- This (software) queue is used to send any broad-/multi-cast buffered
- frames after the next DTIM beacon.
-
- This feature is required for Accesspoint mode operation.
-
- Say Y.
-
-endmenu
-
source "carlfw/usb/Kconfig"
menu "Experimental, Unstable & Testing Extensions"
def_bool y
prompt "Experimental Features"
+config CARL9170FW_PATTERN_GENERATOR
+ def_bool n
+ prompt "Pattern generator"
+ depends on CARL9170FW_EXPERIMENTAL
+ ---help---
+ With this option enabled, the firmware can generate random
+ transmission pattern that might fool a reciever to believe
+ that there is an active radar on the channel.
+ Note: sadly, no SDR here.
+
config CARL9170FW_WOL_OPTION
def_bool n
prompt "Wakeup on WLAN"
def_bool n
depends on CARL9170FW_WOL_OPTION
-config CARL9170FW_WOL_MAGIC_PACKET
+config CARL9170FW_WOL_NL80211_TRIGGERS
def_bool n
- prompt "Magic Packet(tm)"
+ prompt "Standard NL80211 wakeup triggers"
depends on CARL9170FW_WOL_OPTION
select CARL9170FW_WOL
---help---
- Sniff all incoming data frames for the magic packet pattern.
+ Available triggers:
+ * Magic Packet(tm) pattern
+ * disconnect event
config CARL9170FW_WOL_PROBE_REQUEST
def_bool n
prompt "Notify MAC RESET events"
depends on CARL9170FW_FW_MAC_RESET
+config CARL9170FW_80MHZ_CLOCK
+ def_bool n
+ prompt "Allow 80/88MHz clock for HT40"
+ depends on CARL9170FW_EXPERIMENTAL
+ ---help---
+ The SoC can run up to 80/88MHz in HT40 mode. This improves
+ throughput and timing accuracy over the 40/44MHz clock.
+ However some devices don't have heat shields and they with
+ this option enabled, they become unstable under load.
+
config CARL9170FW_BROKEN_FEATURES
def_bool n
- prompt "Broken Featurs"
+ prompt "Broken Features"
config CARL9170FW_DEBUG
def_bool n
endchoice
-
-choice
- prompt "TX / RX Path"
-
- default CARL9170FW_NORMAL_TX_RX
-
- config CARL9170FW_NORMAL_TX_RX
- bool
- prompt "Normal WLAN TX/RX routines"
-
- config CARL9170FW_LOOPBACK
- bool
- depends on CARL9170FW_BROKEN_FEATURES
- prompt "TX->(tx feedback)->RX loopback"
- ---help---
- Useful carlu testcase.
-
- config CARL9170FW_DISCARD
- bool
- depends on CARL9170FW_BROKEN_FEATURES
- prompt "TX->(tx feedback)"
- ---help---
- Useful carlu testcase
-
-endchoice
-
config CARL9170FW_UNUSABLE
def_bool y
- depends on CARL9170FW_BROKEN || CARL9170FW_LOOPBACK
+ depends on CARL9170FW_BROKEN || CARL9170FW_DEBUG
config CARL9170FW_USB_MODESWITCH
def_bool n
prompt "USB 1.1 / 2.0 switching support"
- depends on CARL9170FW_BROKEN_FEATURES
+ depends on CARL9170FW_BROKEN_FEATURES && CARL9170FW_USB_STANDARD_CMDS
---help---
Mostly implemented, but untested and some serious
doubts remain.