1 /* de4x5.c: A DIGITAL DC21x4x DECchip and DE425/DE434/DE435/DE450/DE500
2 ethernet driver for Linux.
4 Copyright 1994, 1995 Digital Equipment Corporation.
6 Testing resources for this driver have been made available
7 in part by NASA Ames Research Center (mjacob@nas.nasa.gov).
9 The author may be reached at davies@maniac.ultranet.com.
11 This program is free software; you can redistribute it and/or modify it
12 under the terms of the GNU General Public License as published by the
13 Free Software Foundation; either version 2 of the License, or (at your
14 option) any later version.
16 THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
17 WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
18 MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
19 NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
20 INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
21 NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
22 USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
23 ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
24 (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
25 THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
27 You should have received a copy of the GNU General Public License along
28 with this program; if not, write to the Free Software Foundation, Inc.,
29 675 Mass Ave, Cambridge, MA 02139, USA.
31 Originally, this driver was written for the Digital Equipment
32 Corporation series of EtherWORKS ethernet cards:
38 DE500 10/100 PCI Fasternet
40 but it will now attempt to support all cards which conform to the
41 Digital Semiconductor SROM Specification. The driver currently
42 recognises the following chips:
50 So far the driver is known to work with the following cards:
58 ZNYX346 10/100 4 port (can act as a 10/100 bridge!)
60 The driver has been tested on a relatively busy network using the DE425,
61 DE434, DE435 and DE500 cards and benchmarked with 'ttcp': it transferred
62 16M of data to a DECstation 5000/200 as follows:
66 DE425 1030k 997k 1170k 1128k
67 DE434 1063k 995k 1170k 1125k
68 DE435 1063k 995k 1170k 1125k
69 DE500 1063k 998k 1170k 1125k in 10Mb/s mode
71 All values are typical (in kBytes/sec) from a sample of 4 for each
72 measurement. Their error is +/-20k on a quiet (private) network and also
73 depend on what load the CPU has.
75 =========================================================================
76 This driver has been written substantially from scratch, although its
77 inheritance of style and stack interface from 'ewrk3.c' and in turn from
78 Donald Becker's 'lance.c' should be obvious. With the module autoload of
79 every usable DECchip board, I pinched Donald's 'next_module' field to
80 link my modules together.
82 Up to 15 EISA cards can be supported under this driver, limited primarily
83 by the available IRQ lines. I have checked different configurations of
84 multiple depca, EtherWORKS 3 cards and de4x5 cards and have not found a
85 problem yet (provided you have at least depca.c v0.38) ...
87 PCI support has been added to allow the driver to work with the DE434,
88 DE435, DE450 and DE500 cards. The I/O accesses are a bit of a kludge due
89 to the differences in the EISA and PCI CSR address offsets from the base
92 The ability to load this driver as a loadable module has been included
93 and used extensively during the driver development (to save those long
94 reboot sequences). Loadable module support under PCI and EISA has been
95 achieved by letting the driver autoprobe as if it were compiled into the
96 kernel. Do make sure you're not sharing interrupts with anything that
97 cannot accommodate interrupt sharing!
99 To utilise this ability, you have to do 8 things:
101 0) have a copy of the loadable modules code installed on your system.
102 1) copy de4x5.c from the /linux/drivers/net directory to your favourite
104 2) for fixed autoprobes (not recommended), edit the source code near
105 line 5594 to reflect the I/O address you're using, or assign these when
108 insmod de4x5 io=0xghh where g = bus number
111 NB: autoprobing for modules is now supported by default. You may just
116 to load all available boards. For a specific board, still use
118 3) compile de4x5.c, but include -DMODULE in the command line to ensure
119 that the correct bits are compiled (see end of source code).
120 4) if you are wanting to add a new card, goto 5. Otherwise, recompile a
121 kernel with the de4x5 configuration turned off and reboot.
122 5) insmod de4x5 [io=0xghh]
123 6) run the net startup bits for your new eth?? interface(s) manually
124 (usually /etc/rc.inet[12] at boot time).
127 To unload a module, turn off the associated interface(s)
128 'ifconfig eth?? down' then 'rmmod de4x5'.
130 Automedia detection is included so that in principal you can disconnect
131 from, e.g. TP, reconnect to BNC and things will still work (after a
132 pause whilst the driver figures out where its media went). My tests
133 using ping showed that it appears to work....
135 By default, the driver will now autodetect any DECchip based card.
136 Should you have a need to restrict the driver to DIGITAL only cards, you
137 can compile with a DEC_ONLY define, or if loading as a module, use the
138 'dec_only=1' parameter.
140 I've changed the timing routines to use the kernel timer and scheduling
141 functions so that the hangs and other assorted problems that occurred
142 while autosensing the media should be gone. A bonus for the DC21040
143 auto media sense algorithm is that it can now use one that is more in
144 line with the rest (the DC21040 chip doesn't have a hardware timer).
145 The downside is the 1 'jiffies' (10ms) resolution.
147 IEEE 802.3u MII interface code has been added in anticipation that some
148 products may use it in the future.
150 The SMC9332 card has a non-compliant SROM which needs fixing - I have
151 patched this driver to detect it because the SROM format used complies
152 to a previous DEC-STD format.
154 I have removed the buffer copies needed for receive on Intels. I cannot
155 remove them for Alphas since the Tulip hardware only does longword
156 aligned DMA transfers and the Alphas get alignment traps with non
157 longword aligned data copies (which makes them really slow). No comment.
159 I have added SROM decoding routines to make this driver work with any
160 card that supports the Digital Semiconductor SROM spec. This will help
161 all cards running the dc2114x series chips in particular. Cards using
162 the dc2104x chips should run correctly with the basic driver. I'm in
163 debt to <mjacob@feral.com> for the testing and feedback that helped get
164 this feature working. So far we have tested KINGSTON, SMC8432, SMC9332
165 (with the latest SROM complying with the SROM spec V3: their first was
166 broken), ZNYX342 and LinkSys. ZYNX314 (dual 21041 MAC) and ZNYX 315
167 (quad 21041 MAC) cards also appear to work despite their incorrectly
170 I have added a temporary fix for interrupt problems when some SCSI cards
171 share the same interrupt as the DECchip based cards. The problem occurs
172 because the SCSI card wants to grab the interrupt as a fast interrupt
173 (runs the service routine with interrupts turned off) vs. this card
174 which really needs to run the service routine with interrupts turned on.
175 This driver will now add the interrupt service routine as a fast
176 interrupt if it is bounced from the slow interrupt. THIS IS NOT A
177 RECOMMENDED WAY TO RUN THE DRIVER and has been done for a limited time
178 until people sort out their compatibility issues and the kernel
179 interrupt service code is fixed. YOU SHOULD SEPARATE OUT THE FAST
180 INTERRUPT CARDS FROM THE SLOW INTERRUPT CARDS to ensure that they do not
181 run on the same interrupt. PCMCIA/CardBus is another can of worms...
183 Finally, I think I have really fixed the module loading problem with
184 more than one DECchip based card. As a side effect, I don't mess with
185 the device structure any more which means that if more than 1 card in
186 2.0.x is installed (4 in 2.1.x), the user will have to edit
187 linux/drivers/net/Space.c to make room for them. Hence, module loading
188 is the preferred way to use this driver, since it doesn't have this
191 Where SROM media detection is used and full duplex is specified in the
192 SROM, the feature is ignored unless lp->params.fdx is set at compile
193 time OR during a module load (insmod de4x5 args='eth??:fdx' [see
194 below]). This is because there is no way to automatically detect full
195 duplex links except through autonegotiation. When I include the
196 autonegotiation feature in the SROM autoconf code, this detection will
197 occur automatically for that case.
199 Command line arguments are now allowed, similar to passing arguments
200 through LILO. This will allow a per adapter board set up of full duplex
201 and media. The only lexical constraints are: the board name (dev->name)
202 appears in the list before its parameters. The list of parameters ends
203 either at the end of the parameter list or with another board name. The
204 following parameters are allowed:
207 autosense to set the media/speed; with the following
209 TP, TP_NW, BNC, AUI, BNC_AUI, 100Mb, 10Mb, AUTO
211 Case sensitivity is important for the sub-parameters. They *must* be
212 upper case. Examples:
214 insmod de4x5 args='eth1:fdx autosense=BNC eth0:autosense=100Mb'.
216 For a compiled in driver, at or above line 548, place e.g.
217 #define DE4X5_PARM "eth0:fdx autosense=AUI eth2:autosense=TP"
219 Yes, I know full duplex isn't permissible on BNC or AUI; they're just
220 examples. By default, full duplex is turned off and AUTO is the default
221 autosense setting. In reality, I expect only the full duplex option to
222 be used. Note the use of single quotes in the two examples above and the
223 lack of commas to separate items. ALSO, you must get the requested media
224 correct in relation to what the adapter SROM says it has. There's no way
225 to determine this in advance other than by trial and error and common
226 sense, e.g. call a BNC connectored port 'BNC', not '10Mb'.
228 Changed the bus probing. EISA used to be done first, followed by PCI.
229 Most people probably don't even know what a de425 is today and the EISA
230 probe has messed up some SCSI cards in the past, so now PCI is always
231 probed first followed by EISA if a) the architecture allows EISA and
232 either b) there have been no PCI cards detected or c) an EISA probe is
233 forced by the user. To force a probe include "force_eisa" in your
234 insmod "args" line; for built-in kernels either change the driver to do
235 this automatically or include #define DE4X5_FORCE_EISA on or before
236 line 1040 in the driver.
244 Version Date Description
246 0.1 17-Nov-94 Initial writing. ALPHA code release.
247 0.2 13-Jan-95 Added PCI support for DE435's.
248 0.21 19-Jan-95 Added auto media detection.
249 0.22 10-Feb-95 Fix interrupt handler call <chris@cosy.sbg.ac.at>.
250 Fix recognition bug reported by <bkm@star.rl.ac.uk>.
251 Add request/release_region code.
252 Add loadable modules support for PCI.
253 Clean up loadable modules support.
254 0.23 28-Feb-95 Added DC21041 and DC21140 support.
255 Fix missed frame counter value and initialisation.
257 0.24 11-Apr-95 Change delay routine to use <linux/udelay>.
258 Change TX_BUFFS_AVAIL macro.
259 Change media autodetection to allow manual setting.
260 Completed DE500 (DC21140) support.
261 0.241 18-Apr-95 Interim release without DE500 Autosense Algorithm.
262 0.242 10-May-95 Minor changes.
263 0.30 12-Jun-95 Timer fix for DC21140.
265 Add ALPHA changes from <jestabro@ant.tay1.dec.com>.
266 Add DE500 semi automatic autosense.
267 Add Link Fail interrupt TP failure detection.
268 Add timer based link change detection.
269 Plugged a memory leak in de4x5_queue_pkt().
270 0.31 13-Jun-95 Fixed PCI stuff for 1.3.1.
271 0.32 26-Jun-95 Added verify_area() calls in de4x5_ioctl() from a
272 suggestion by <heiko@colossus.escape.de>.
273 0.33 8-Aug-95 Add shared interrupt support (not released yet).
274 0.331 21-Aug-95 Fix de4x5_open() with fast CPUs.
275 Fix de4x5_interrupt().
276 Fix dc21140_autoconf() mess.
277 No shared interrupt support.
278 0.332 11-Sep-95 Added MII management interface routines.
279 0.40 5-Mar-96 Fix setup frame timeout <maartenb@hpkuipc.cern.ch>.
280 Add kernel timer code (h/w is too flaky).
281 Add MII based PHY autosense.
282 Add new multicasting code.
283 Add new autosense algorithms for media/mode
284 selection using kernel scheduling/timing.
286 Made changes suggested by <jeff@router.patch.net>:
287 Change driver to detect all DECchip based cards
288 with DEC_ONLY restriction a special case.
289 Changed driver to autoprobe as a module. No irq
290 checking is done now - assume BIOS is good!
291 Added SMC9332 detection <manabe@Roy.dsl.tutics.ac.jp>
292 0.41 21-Mar-96 Don't check for get_hw_addr checksum unless DEC card
293 only <niles@axp745gsfc.nasa.gov>
294 Fix for multiple PCI cards reported by <jos@xos.nl>
295 Duh, put the IRQF_SHARED flag into request_interrupt().
296 Fix SMC ethernet address in enet_det[].
297 Print chip name instead of "UNKNOWN" during boot.
298 0.42 26-Apr-96 Fix MII write TA bit error.
299 Fix bug in dc21040 and dc21041 autosense code.
300 Remove buffer copies on receive for Intels.
301 Change sk_buff handling during media disconnects to
302 eliminate DUP packets.
303 Add dynamic TX thresholding.
304 Change all chips to use perfect multicast filtering.
305 Fix alloc_device() bug <jari@markkus2.fimr.fi>
306 0.43 21-Jun-96 Fix unconnected media TX retry bug.
307 Add Accton to the list of broken cards.
308 Fix TX under-run bug for non DC21140 chips.
309 Fix boot command probe bug in alloc_device() as
310 reported by <koen.gadeyne@barco.com> and
311 <orava@nether.tky.hut.fi>.
312 Add cache locks to prevent a race condition as
313 reported by <csd@microplex.com> and
314 <baba@beckman.uiuc.edu>.
315 Upgraded alloc_device() code.
316 0.431 28-Jun-96 Fix potential bug in queue_pkt() from discussion
317 with <csd@microplex.com>
318 0.44 13-Aug-96 Fix RX overflow bug in 2114[023] chips.
319 Fix EISA probe bugs reported by <os2@kpi.kharkov.ua>
320 and <michael@compurex.com>.
321 0.441 9-Sep-96 Change dc21041_autoconf() to probe quiet BNC media
322 with a loopback packet.
323 0.442 9-Sep-96 Include AUI in dc21041 media printout. Bug reported
324 by <bhat@mundook.cs.mu.OZ.AU>
325 0.45 8-Dec-96 Include endian functions for PPC use, from work
326 by <cort@cs.nmt.edu> and <g.thomas@opengroup.org>.
327 0.451 28-Dec-96 Added fix to allow autoprobe for modules after
328 suggestion from <mjacob@feral.com>.
329 0.5 30-Jan-97 Added SROM decoding functions.
331 Fix sleep/wakeup calls for PCI cards, bug reported
332 by <cross@gweep.lkg.dec.com>.
333 Added multi-MAC, one SROM feature from discussion
334 with <mjacob@feral.com>.
335 Added full module autoprobe capability.
336 Added attempt to use an SMC9332 with broken SROM.
337 Added fix for ZYNX multi-mac cards that didn't
338 get their IRQs wired correctly.
339 0.51 13-Feb-97 Added endian fixes for the SROM accesses from
341 Fix init_connection() to remove extra device reset.
342 Fix MAC/PHY reset ordering in dc21140m_autoconf().
343 Fix initialisation problem with lp->timeout in
344 typeX_infoblock() from <paubert@iram.es>.
345 Fix MII PHY reset problem from work done by
347 0.52 26-Apr-97 Some changes may not credit the right people -
348 a disk crash meant I lost some mail.
349 Change RX interrupt routine to drop rather than
350 defer packets to avoid hang reported by
351 <g.thomas@opengroup.org>.
352 Fix srom_exec() to return for COMPACT and type 1
354 Added DC21142 and DC21143 functions.
355 Added byte counters from <phil@tazenda.demon.co.uk>
356 Added IRQF_DISABLED temporary fix from
358 0.53 12-Nov-97 Fix the *_probe() to include 'eth??' name during
359 module load: bug reported by
360 <Piete.Brooks@cl.cam.ac.uk>
361 Fix multi-MAC, one SROM, to work with 2114x chips:
362 bug reported by <cmetz@inner.net>.
363 Make above search independent of BIOS device scan
365 Completed DC2114[23] autosense functions.
366 0.531 21-Dec-97 Fix DE500-XA 100Mb/s bug reported by
368 Fix type1_infoblock() bug introduced in 0.53, from
370 <parmee@postecss.ncrfran.france.ncr.com> and
371 <jo@ice.dillingen.baynet.de>.
372 Added argument list to set up each board from either
373 a module's command line or a compiled in #define.
374 Added generic MII PHY functionality to deal with
376 Fix the mess in 2.1.67.
377 0.532 5-Jan-98 Fix bug in mii_get_phy() reported by
379 Fix bug in pci_probe() for 64 bit systems reported
380 by <belliott@accessone.com>.
381 0.533 9-Jan-98 Fix more 64 bit bugs reported by <jal@cs.brown.edu>.
382 0.534 24-Jan-98 Fix last (?) endian bug from <geert@linux-m68k.org>
383 0.535 21-Feb-98 Fix Ethernet Address PROM reset bug for DC21040.
384 0.536 21-Mar-98 Change pci_probe() to use the pci_dev structure.
385 **Incompatible with 2.0.x from here.**
386 0.540 5-Jul-98 Atomicize assertion of dev->interrupt for SMP
387 from <lma@varesearch.com>
388 Add TP, AUI and BNC cases to 21140m_autoconf() for
389 case where a 21140 under SROM control uses, e.g. AUI
390 from problem report by <delchini@lpnp09.in2p3.fr>
391 Add MII parallel detection to 2114x_autoconf() for
392 case where no autonegotiation partner exists from
393 problem report by <mlapsley@ndirect.co.uk>.
394 Add ability to force connection type directly even
395 when using SROM control from problem report by
397 Updated the PCI interface to conform with the latest
398 version. I hope nothing is broken...
399 Add TX done interrupt modification from suggestion
400 by <Austin.Donnelly@cl.cam.ac.uk>.
401 Fix is_anc_capable() bug reported by
402 <Austin.Donnelly@cl.cam.ac.uk>.
403 Fix type[13]_infoblock() bug: during MII search, PHY
404 lp->rst not run because lp->ibn not initialised -
405 from report & fix by <paubert@iram.es>.
406 Fix probe bug with EISA & PCI cards present from
407 report by <eirik@netcom.com>.
408 0.541 24-Aug-98 Fix compiler problems associated with i386-string
409 ops from multiple bug reports and temporary fix
410 from <paubert@iram.es>.
411 Fix pci_probe() to correctly emulate the old
412 pcibios_find_class() function.
413 Add an_exception() for old ZYNX346 and fix compile
414 warning on PPC & SPARC, from <ecd@skynet.be>.
415 Fix lastPCI to correctly work with compiled in
416 kernels and modules from bug report by
417 <Zlatko.Calusic@CARNet.hr> et al.
418 0.542 15-Sep-98 Fix dc2114x_autoconf() to stop multiple messages
419 when media is unconnected.
420 Change dev->interrupt to lp->interrupt to ensure
421 alignment for Alpha's and avoid their unaligned
422 access traps. This flag is merely for log messages:
423 should do something more definitive though...
424 0.543 30-Dec-98 Add SMP spin locking.
425 0.544 8-May-99 Fix for buggy SROM in Motorola embedded boards using
426 a 21143 by <mmporter@home.com>.
427 Change PCI/EISA bus probing order.
428 0.545 28-Nov-99 Further Moto SROM bug fix from
429 <mporter@eng.mcd.mot.com>
430 Remove double checking for DEBUG_RX in de4x5_dbg_rx()
431 from report by <geert@linux-m68k.org>
432 0.546 22-Feb-01 Fixes Alpha XP1000 oops. The srom_search function
433 was causing a page fault when initializing the
434 variable 'pb', on a non de4x5 PCI device, in this
435 case a PCI bridge (DEC chip 21152). The value of
436 'pb' is now only initialized if a de4x5 chip is
438 <france@handhelds.org>
439 0.547 08-Nov-01 Use library crc32 functions by <Matt_Domsch@dell.com>
440 0.548 30-Aug-03 Big 2.6 cleanup. Ported to PCI/EISA probing and
441 generic DMA APIs. Fixed DE425 support on Alpha.
442 <maz@wild-wind.fr.eu.org>
443 =========================================================================
446 #include <linux/module.h>
447 #include <linux/kernel.h>
448 #include <linux/string.h>
449 #include <linux/interrupt.h>
450 #include <linux/ptrace.h>
451 #include <linux/errno.h>
452 #include <linux/ioport.h>
453 #include <linux/pci.h>
454 #include <linux/eisa.h>
455 #include <linux/delay.h>
456 #include <linux/init.h>
457 #include <linux/spinlock.h>
458 #include <linux/crc32.h>
459 #include <linux/netdevice.h>
460 #include <linux/etherdevice.h>
461 #include <linux/skbuff.h>
462 #include <linux/time.h>
463 #include <linux/types.h>
464 #include <linux/unistd.h>
465 #include <linux/ctype.h>
466 #include <linux/dma-mapping.h>
467 #include <linux/moduleparam.h>
468 #include <linux/bitops.h>
469 #include <linux/gfp.h>
473 #include <asm/byteorder.h>
474 #include <asm/unaligned.h>
475 #include <asm/uaccess.h>
476 #ifdef CONFIG_PPC_PMAC
477 #include <asm/machdep.h>
478 #endif /* CONFIG_PPC_PMAC */
482 static const char version[] =
483 KERN_INFO "de4x5.c:V0.546 2001/02/22 davies@maniac.ultranet.com\n";
485 #define c_char const char
491 int reset; /* Hard reset required? */
492 int id; /* IEEE OUI */
493 int ta; /* One cycle TA time - 802.3u is confusing here */
494 struct { /* Non autonegotiation (parallel) speed det. */
502 int reset; /* Hard reset required? */
503 int id; /* IEEE OUI */
504 int ta; /* One cycle TA time */
505 struct { /* Non autonegotiation (parallel) speed det. */
510 int addr; /* MII address for the PHY */
511 u_char *gep; /* Start of GEP sequence block in SROM */
512 u_char *rst; /* Start of reset sequence in SROM */
513 u_int mc; /* Media Capabilities */
514 u_int ana; /* NWay Advertisement */
515 u_int fdx; /* Full DupleX capabilities for each media */
516 u_int ttm; /* Transmit Threshold Mode for each media */
517 u_int mci; /* 21142 MII Connector Interrupt info */
520 #define DE4X5_MAX_PHY 8 /* Allow up to 8 attached PHY devices per board */
523 u_char mc; /* Media Code */
524 u_char ext; /* csr13-15 valid when set */
525 int csr13; /* SIA Connectivity Register */
526 int csr14; /* SIA TX/RX Register */
527 int csr15; /* SIA General Register */
528 int gepc; /* SIA GEP Control Information */
529 int gep; /* SIA GEP Data */
533 ** Define the know universe of PHY devices that can be
534 ** recognised by this driver.
536 static struct phy_table phy_info[] = {
537 {0, NATIONAL_TX, 1, {0x19, 0x40, 0x00}}, /* National TX */
538 {1, BROADCOM_T4, 1, {0x10, 0x02, 0x02}}, /* Broadcom T4 */
539 {0, SEEQ_T4 , 1, {0x12, 0x10, 0x10}}, /* SEEQ T4 */
540 {0, CYPRESS_T4 , 1, {0x05, 0x20, 0x20}}, /* Cypress T4 */
541 {0, 0x7810 , 1, {0x14, 0x0800, 0x0800}} /* Level One LTX970 */
545 ** These GENERIC values assumes that the PHY devices follow 802.3u and
546 ** allow parallel detection to set the link partner ability register.
547 ** Detection of 100Base-TX [H/F Duplex] and 100Base-T4 is supported.
549 #define GENERIC_REG 0x05 /* Autoneg. Link Partner Advertisement Reg. */
550 #define GENERIC_MASK MII_ANLPA_100M /* All 100Mb/s Technologies */
551 #define GENERIC_VALUE MII_ANLPA_100M /* 100B-TX, 100B-TX FDX, 100B-T4 */
554 ** Define special SROM detection cases
556 static c_char enet_det[][ETH_ALEN] = {
557 {0x00, 0x00, 0xc0, 0x00, 0x00, 0x00},
558 {0x00, 0x00, 0xe8, 0x00, 0x00, 0x00}
565 ** SROM Repair definitions. If a broken SROM is detected a card may
566 ** use this information to help figure out what to do. This is a
567 ** "stab in the dark" and so far for SMC9332's only.
569 static c_char srom_repair_info[][100] = {
570 {0x00,0x1e,0x00,0x00,0x00,0x08, /* SMC9332 */
571 0x1f,0x01,0x8f,0x01,0x00,0x01,0x00,0x02,
572 0x01,0x00,0x00,0x78,0xe0,0x01,0x00,0x50,
578 static int de4x5_debug = DE4X5_DEBUG;
580 /*static int de4x5_debug = (DEBUG_MII | DEBUG_SROM | DEBUG_PCICFG | DEBUG_MEDIA | DEBUG_VERSION);*/
581 static int de4x5_debug = (DEBUG_MEDIA | DEBUG_VERSION);
585 ** Allow per adapter set up. For modules this is simply a command line
587 ** insmod de4x5 args='eth1:fdx autosense=BNC eth0:autosense=100Mb'.
589 ** For a compiled in driver, place e.g.
590 ** #define DE4X5_PARM "eth0:fdx autosense=AUI eth2:autosense=TP"
594 static char *args = DE4X5_PARM;
604 #define DE4X5_AUTOSENSE_MS 250 /* msec autosense tick (DE500) */
606 #define DE4X5_NDA 0xffe0 /* No Device (I/O) Address */
609 ** Ethernet PROM defines
611 #define PROBE_LENGTH 32
612 #define ETH_PROM_SIG 0xAA5500FFUL
617 #define PKT_BUF_SZ 1536 /* Buffer size for each Tx/Rx buffer */
618 #define IEEE802_3_SZ 1518 /* Packet + CRC */
619 #define MAX_PKT_SZ 1514 /* Maximum ethernet packet length */
620 #define MAX_DAT_SZ 1500 /* Maximum ethernet data length */
621 #define MIN_DAT_SZ 1 /* Minimum ethernet data length */
622 #define PKT_HDR_LEN 14 /* Addresses and data length info */
623 #define FAKE_FRAME_LEN (MAX_PKT_SZ + 1)
624 #define QUEUE_PKT_TIMEOUT (3*HZ) /* 3 second timeout */
630 #define DE4X5_EISA_IO_PORTS 0x0c00 /* I/O port base address, slot 0 */
631 #define DE4X5_EISA_TOTAL_SIZE 0x100 /* I/O address extent */
633 #define EISA_ALLOWED_IRQ_LIST {5, 9, 10, 11}
635 #define DE4X5_SIGNATURE {"DE425","DE434","DE435","DE450","DE500"}
636 #define DE4X5_NAME_LENGTH 8
638 static c_char *de4x5_signatures[] = DE4X5_SIGNATURE;
641 ** Ethernet PROM defines for DC21040
643 #define PROBE_LENGTH 32
644 #define ETH_PROM_SIG 0xAA5500FFUL
649 #define PCI_MAX_BUS_NUM 8
650 #define DE4X5_PCI_TOTAL_SIZE 0x80 /* I/O address extent */
651 #define DE4X5_CLASS_CODE 0x00020000 /* Network controller, Ethernet */
654 ** Memory Alignment. Each descriptor is 4 longwords long. To force a
655 ** particular alignment on the TX descriptor, adjust DESC_SKIP_LEN and
656 ** DESC_ALIGN. ALIGN aligns the start address of the private memory area
657 ** and hence the RX descriptor ring's first entry.
659 #define DE4X5_ALIGN4 ((u_long)4 - 1) /* 1 longword align */
660 #define DE4X5_ALIGN8 ((u_long)8 - 1) /* 2 longword align */
661 #define DE4X5_ALIGN16 ((u_long)16 - 1) /* 4 longword align */
662 #define DE4X5_ALIGN32 ((u_long)32 - 1) /* 8 longword align */
663 #define DE4X5_ALIGN64 ((u_long)64 - 1) /* 16 longword align */
664 #define DE4X5_ALIGN128 ((u_long)128 - 1) /* 32 longword align */
666 #define DE4X5_ALIGN DE4X5_ALIGN32 /* Keep the DC21040 happy... */
667 #define DE4X5_CACHE_ALIGN CAL_16LONG
668 #define DESC_SKIP_LEN DSL_0 /* Must agree with DESC_ALIGN */
669 /*#define DESC_ALIGN u32 dummy[4]; / * Must agree with DESC_SKIP_LEN */
672 #ifndef DEC_ONLY /* See README.de4x5 for using this */
675 static int dec_only = 1;
679 ** DE4X5 IRQ ENABLE/DISABLE
681 #define ENABLE_IRQs { \
683 outl(imr, DE4X5_IMR); /* Enable the IRQs */\
686 #define DISABLE_IRQs {\
687 imr = inl(DE4X5_IMR);\
689 outl(imr, DE4X5_IMR); /* Disable the IRQs */\
692 #define UNMASK_IRQs {\
693 imr |= lp->irq_mask;\
694 outl(imr, DE4X5_IMR); /* Unmask the IRQs */\
698 imr = inl(DE4X5_IMR);\
699 imr &= ~lp->irq_mask;\
700 outl(imr, DE4X5_IMR); /* Mask the IRQs */\
706 #define START_DE4X5 {\
707 omr = inl(DE4X5_OMR);\
708 omr |= OMR_ST | OMR_SR;\
709 outl(omr, DE4X5_OMR); /* Enable the TX and/or RX */\
712 #define STOP_DE4X5 {\
713 omr = inl(DE4X5_OMR);\
714 omr &= ~(OMR_ST|OMR_SR);\
715 outl(omr, DE4X5_OMR); /* Disable the TX and/or RX */ \
721 #define RESET_SIA outl(0, DE4X5_SICR); /* Reset SIA connectivity regs */
724 ** DE500 AUTOSENSE TIMER INTERVAL (MILLISECS)
726 #define DE4X5_AUTOSENSE_MS 250
732 char sub_vendor_id[2];
733 char sub_system_id[2];
738 char num_controllers;
743 #define SUB_VENDOR_ID 0x500a
746 ** DE4X5 Descriptors. Make sure that all the RX buffers are contiguous
747 ** and have sizes of both a power of 2 and a multiple of 4.
748 ** A size of 256 bytes for each buffer could be chosen because over 90% of
749 ** all packets in our network are <256 bytes long and 64 longword alignment
750 ** is possible. 1536 showed better 'ttcp' performance. Take your pick. 32 TX
751 ** descriptors are needed for machines with an ALPHA CPU.
753 #define NUM_RX_DESC 8 /* Number of RX descriptors */
754 #define NUM_TX_DESC 32 /* Number of TX descriptors */
755 #define RX_BUFF_SZ 1536 /* Power of 2 for kmalloc and */
756 /* Multiple of 4 for DC21040 */
757 /* Allows 512 byte alignment */
759 volatile __le32 status;
767 ** The DE4X5 private structure
769 #define DE4X5_PKT_STAT_SZ 16
770 #define DE4X5_PKT_BIN_SZ 128 /* Should be >=100 unless you
771 increase DE4X5_PKT_STAT_SZ */
774 u_int bins[DE4X5_PKT_STAT_SZ]; /* Private stats counters */
778 u_int excessive_collisions;
780 u_int excessive_underruns;
781 u_int rx_runt_frames;
787 struct de4x5_private {
788 char adapter_name[80]; /* Adapter name */
789 u_long interrupt; /* Aligned ISR flag */
790 struct de4x5_desc *rx_ring; /* RX descriptor ring */
791 struct de4x5_desc *tx_ring; /* TX descriptor ring */
792 struct sk_buff *tx_skb[NUM_TX_DESC]; /* TX skb for freeing when sent */
793 struct sk_buff *rx_skb[NUM_RX_DESC]; /* RX skb's */
794 int rx_new, rx_old; /* RX descriptor ring pointers */
795 int tx_new, tx_old; /* TX descriptor ring pointers */
796 char setup_frame[SETUP_FRAME_LEN]; /* Holds MCA and PA info. */
797 char frame[64]; /* Min sized packet for loopback*/
798 spinlock_t lock; /* Adapter specific spinlock */
799 struct net_device_stats stats; /* Public stats */
800 struct pkt_stats pktStats; /* Private stats counters */
803 int bus; /* EISA or PCI */
804 int bus_num; /* PCI Bus number */
805 int device; /* Device number on PCI bus */
806 int state; /* Adapter OPENED or CLOSED */
807 int chipset; /* DC21040, DC21041 or DC21140 */
808 s32 irq_mask; /* Interrupt Mask (Enable) bits */
809 s32 irq_en; /* Summary interrupt bits */
810 int media; /* Media (eg TP), mode (eg 100B)*/
811 int c_media; /* Remember the last media conn */
812 bool fdx; /* media full duplex flag */
813 int linkOK; /* Link is OK */
814 int autosense; /* Allow/disallow autosensing */
815 bool tx_enable; /* Enable descriptor polling */
816 int setup_f; /* Setup frame filtering type */
817 int local_state; /* State within a 'media' state */
818 struct mii_phy phy[DE4X5_MAX_PHY]; /* List of attached PHY devices */
819 struct sia_phy sia; /* SIA PHY Information */
820 int active; /* Index to active PHY device */
821 int mii_cnt; /* Number of attached PHY's */
822 int timeout; /* Scheduling counter */
823 struct timer_list timer; /* Timer info for kernel */
824 int tmp; /* Temporary global per card */
826 u_long lock; /* Lock the cache accesses */
827 s32 csr0; /* Saved Bus Mode Register */
828 s32 csr6; /* Saved Operating Mode Reg. */
829 s32 csr7; /* Saved IRQ Mask Register */
830 s32 gep; /* Saved General Purpose Reg. */
831 s32 gepc; /* Control info for GEP */
832 s32 csr13; /* Saved SIA Connectivity Reg. */
833 s32 csr14; /* Saved SIA TX/RX Register */
834 s32 csr15; /* Saved SIA General Register */
835 int save_cnt; /* Flag if state already saved */
836 struct sk_buff_head queue; /* Save the (re-ordered) skb's */
838 struct de4x5_srom srom; /* A copy of the SROM */
839 int cfrv; /* Card CFRV copy */
840 int rx_ovf; /* Check for 'RX overflow' tag */
841 bool useSROM; /* For non-DEC card use SROM */
842 bool useMII; /* Infoblock using the MII */
843 int asBitValid; /* Autosense bits in GEP? */
844 int asPolarity; /* 0 => asserted high */
845 int asBit; /* Autosense bit number in GEP */
846 int defMedium; /* SROM default medium */
847 int tcount; /* Last infoblock number */
848 int infoblock_init; /* Initialised this infoblock? */
849 int infoleaf_offset; /* SROM infoleaf for controller */
850 s32 infoblock_csr6; /* csr6 value in SROM infoblock */
851 int infoblock_media; /* infoblock media */
852 int (*infoleaf_fn)(struct net_device *); /* Pointer to infoleaf function */
853 u_char *rst; /* Pointer to Type 5 reset info */
854 u_char ibn; /* Infoblock number */
855 struct parameters params; /* Command line/ #defined params */
856 struct device *gendev; /* Generic device */
857 dma_addr_t dma_rings; /* DMA handle for rings */
858 int dma_size; /* Size of the DMA area */
859 char *rx_bufs; /* rx bufs on alpha, sparc, ... */
863 ** To get around certain poxy cards that don't provide an SROM
864 ** for the second and more DECchip, I have to key off the first
865 ** chip's address. I'll assume there's not a bad SROM iff:
867 ** o the chipset is the same
868 ** o the bus number is the same and > 0
869 ** o the sum of all the returned hw address bytes is 0 or 0x5fa
871 ** Also have to save the irq for those cards whose hardware designers
872 ** can't follow the PCI to PCI Bridge Architecture spec.
878 u_char addr[ETH_ALEN];
882 ** The transmit ring full condition is described by the tx_old and tx_new
884 ** tx_old = tx_new Empty ring
885 ** tx_old = tx_new+1 Full ring
886 ** tx_old+txRingSize = tx_new+1 Full ring (wrapped condition)
888 #define TX_BUFFS_AVAIL ((lp->tx_old<=lp->tx_new)?\
889 lp->tx_old+lp->txRingSize-lp->tx_new-1:\
890 lp->tx_old -lp->tx_new-1)
892 #define TX_PKT_PENDING (lp->tx_old != lp->tx_new)
897 static int de4x5_open(struct net_device *dev);
898 static netdev_tx_t de4x5_queue_pkt(struct sk_buff *skb,
899 struct net_device *dev);
900 static irqreturn_t de4x5_interrupt(int irq, void *dev_id);
901 static int de4x5_close(struct net_device *dev);
902 static struct net_device_stats *de4x5_get_stats(struct net_device *dev);
903 static void de4x5_local_stats(struct net_device *dev, char *buf, int pkt_len);
904 static void set_multicast_list(struct net_device *dev);
905 static int de4x5_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
910 static int de4x5_hw_init(struct net_device *dev, u_long iobase, struct device *gendev);
911 static int de4x5_init(struct net_device *dev);
912 static int de4x5_sw_reset(struct net_device *dev);
913 static int de4x5_rx(struct net_device *dev);
914 static int de4x5_tx(struct net_device *dev);
915 static void de4x5_ast(struct net_device *dev);
916 static int de4x5_txur(struct net_device *dev);
917 static int de4x5_rx_ovfc(struct net_device *dev);
919 static int autoconf_media(struct net_device *dev);
920 static void create_packet(struct net_device *dev, char *frame, int len);
921 static void load_packet(struct net_device *dev, char *buf, u32 flags, struct sk_buff *skb);
922 static int dc21040_autoconf(struct net_device *dev);
923 static int dc21041_autoconf(struct net_device *dev);
924 static int dc21140m_autoconf(struct net_device *dev);
925 static int dc2114x_autoconf(struct net_device *dev);
926 static int srom_autoconf(struct net_device *dev);
927 static int de4x5_suspect_state(struct net_device *dev, int timeout, int prev_state, int (*fn)(struct net_device *, int), int (*asfn)(struct net_device *));
928 static int dc21040_state(struct net_device *dev, int csr13, int csr14, int csr15, int timeout, int next_state, int suspect_state, int (*fn)(struct net_device *, int));
929 static int test_media(struct net_device *dev, s32 irqs, s32 irq_mask, s32 csr13, s32 csr14, s32 csr15, s32 msec);
930 static int test_for_100Mb(struct net_device *dev, int msec);
931 static int wait_for_link(struct net_device *dev);
932 static int test_mii_reg(struct net_device *dev, int reg, int mask, bool pol, long msec);
933 static int is_spd_100(struct net_device *dev);
934 static int is_100_up(struct net_device *dev);
935 static int is_10_up(struct net_device *dev);
936 static int is_anc_capable(struct net_device *dev);
937 static int ping_media(struct net_device *dev, int msec);
938 static struct sk_buff *de4x5_alloc_rx_buff(struct net_device *dev, int index, int len);
939 static void de4x5_free_rx_buffs(struct net_device *dev);
940 static void de4x5_free_tx_buffs(struct net_device *dev);
941 static void de4x5_save_skbs(struct net_device *dev);
942 static void de4x5_rst_desc_ring(struct net_device *dev);
943 static void de4x5_cache_state(struct net_device *dev, int flag);
944 static void de4x5_put_cache(struct net_device *dev, struct sk_buff *skb);
945 static void de4x5_putb_cache(struct net_device *dev, struct sk_buff *skb);
946 static struct sk_buff *de4x5_get_cache(struct net_device *dev);
947 static void de4x5_setup_intr(struct net_device *dev);
948 static void de4x5_init_connection(struct net_device *dev);
949 static int de4x5_reset_phy(struct net_device *dev);
950 static void reset_init_sia(struct net_device *dev, s32 sicr, s32 strr, s32 sigr);
951 static int test_ans(struct net_device *dev, s32 irqs, s32 irq_mask, s32 msec);
952 static int test_tp(struct net_device *dev, s32 msec);
953 static int EISA_signature(char *name, struct device *device);
954 static int PCI_signature(char *name, struct de4x5_private *lp);
955 static void DevicePresent(struct net_device *dev, u_long iobase);
956 static void enet_addr_rst(u_long aprom_addr);
957 static int de4x5_bad_srom(struct de4x5_private *lp);
958 static short srom_rd(u_long address, u_char offset);
959 static void srom_latch(u_int command, u_long address);
960 static void srom_command(u_int command, u_long address);
961 static void srom_address(u_int command, u_long address, u_char offset);
962 static short srom_data(u_int command, u_long address);
963 /*static void srom_busy(u_int command, u_long address);*/
964 static void sendto_srom(u_int command, u_long addr);
965 static int getfrom_srom(u_long addr);
966 static int srom_map_media(struct net_device *dev);
967 static int srom_infoleaf_info(struct net_device *dev);
968 static void srom_init(struct net_device *dev);
969 static void srom_exec(struct net_device *dev, u_char *p);
970 static int mii_rd(u_char phyreg, u_char phyaddr, u_long ioaddr);
971 static void mii_wr(int data, u_char phyreg, u_char phyaddr, u_long ioaddr);
972 static int mii_rdata(u_long ioaddr);
973 static void mii_wdata(int data, int len, u_long ioaddr);
974 static void mii_ta(u_long rw, u_long ioaddr);
975 static int mii_swap(int data, int len);
976 static void mii_address(u_char addr, u_long ioaddr);
977 static void sendto_mii(u32 command, int data, u_long ioaddr);
978 static int getfrom_mii(u32 command, u_long ioaddr);
979 static int mii_get_oui(u_char phyaddr, u_long ioaddr);
980 static int mii_get_phy(struct net_device *dev);
981 static void SetMulticastFilter(struct net_device *dev);
982 static int get_hw_addr(struct net_device *dev);
983 static void srom_repair(struct net_device *dev, int card);
984 static int test_bad_enet(struct net_device *dev, int status);
985 static int an_exception(struct de4x5_private *lp);
986 static char *build_setup_frame(struct net_device *dev, int mode);
987 static void disable_ast(struct net_device *dev);
988 static long de4x5_switch_mac_port(struct net_device *dev);
989 static int gep_rd(struct net_device *dev);
990 static void gep_wr(s32 data, struct net_device *dev);
991 static void yawn(struct net_device *dev, int state);
992 static void de4x5_parse_params(struct net_device *dev);
993 static void de4x5_dbg_open(struct net_device *dev);
994 static void de4x5_dbg_mii(struct net_device *dev, int k);
995 static void de4x5_dbg_media(struct net_device *dev);
996 static void de4x5_dbg_srom(struct de4x5_srom *p);
997 static void de4x5_dbg_rx(struct sk_buff *skb, int len);
998 static int dc21041_infoleaf(struct net_device *dev);
999 static int dc21140_infoleaf(struct net_device *dev);
1000 static int dc21142_infoleaf(struct net_device *dev);
1001 static int dc21143_infoleaf(struct net_device *dev);
1002 static int type0_infoblock(struct net_device *dev, u_char count, u_char *p);
1003 static int type1_infoblock(struct net_device *dev, u_char count, u_char *p);
1004 static int type2_infoblock(struct net_device *dev, u_char count, u_char *p);
1005 static int type3_infoblock(struct net_device *dev, u_char count, u_char *p);
1006 static int type4_infoblock(struct net_device *dev, u_char count, u_char *p);
1007 static int type5_infoblock(struct net_device *dev, u_char count, u_char *p);
1008 static int compact_infoblock(struct net_device *dev, u_char count, u_char *p);
1011 ** Note now that module autoprobing is allowed under EISA and PCI. The
1012 ** IRQ lines will not be auto-detected; instead I'll rely on the BIOSes
1013 ** to "do the right thing".
1016 static int io=0x0;/* EDIT THIS LINE FOR YOUR CONFIGURATION IF NEEDED */
1018 module_param(io, int, 0);
1019 module_param(de4x5_debug, int, 0);
1020 module_param(dec_only, int, 0);
1021 module_param(args, charp, 0);
1023 MODULE_PARM_DESC(io, "de4x5 I/O base address");
1024 MODULE_PARM_DESC(de4x5_debug, "de4x5 debug mask");
1025 MODULE_PARM_DESC(dec_only, "de4x5 probe only for Digital boards (0-1)");
1026 MODULE_PARM_DESC(args, "de4x5 full duplex and media type settings; see de4x5.c for details");
1027 MODULE_LICENSE("GPL");
1030 ** List the SROM infoleaf functions and chipsets
1034 int (*fn)(struct net_device *);
1036 static struct InfoLeaf infoleaf_array[] = {
1037 {DC21041, dc21041_infoleaf},
1038 {DC21140, dc21140_infoleaf},
1039 {DC21142, dc21142_infoleaf},
1040 {DC21143, dc21143_infoleaf}
1042 #define INFOLEAF_SIZE ARRAY_SIZE(infoleaf_array)
1045 ** List the SROM info block functions
1047 static int (*dc_infoblock[])(struct net_device *dev, u_char, u_char *) = {
1057 #define COMPACT (ARRAY_SIZE(dc_infoblock) - 1)
1060 ** Miscellaneous defines...
1062 #define RESET_DE4X5 {\
1066 outl(i | BMR_SWR, DE4X5_BMR);\
1068 outl(i, DE4X5_BMR);\
1070 for (i=0;i<5;i++) {inl(DE4X5_BMR); mdelay(1);}\
1074 #define PHY_HARD_RESET {\
1075 outl(GEP_HRST, DE4X5_GEP); /* Hard RESET the PHY dev. */\
1076 mdelay(1); /* Assert for 1ms */\
1077 outl(0x00, DE4X5_GEP);\
1078 mdelay(2); /* Wait for 2ms */\
1081 static const struct net_device_ops de4x5_netdev_ops = {
1082 .ndo_open = de4x5_open,
1083 .ndo_stop = de4x5_close,
1084 .ndo_start_xmit = de4x5_queue_pkt,
1085 .ndo_get_stats = de4x5_get_stats,
1086 .ndo_set_rx_mode = set_multicast_list,
1087 .ndo_do_ioctl = de4x5_ioctl,
1088 .ndo_change_mtu = eth_change_mtu,
1089 .ndo_set_mac_address= eth_mac_addr,
1090 .ndo_validate_addr = eth_validate_addr,
1095 de4x5_hw_init(struct net_device *dev, u_long iobase, struct device *gendev)
1097 char name[DE4X5_NAME_LENGTH + 1];
1098 struct de4x5_private *lp = netdev_priv(dev);
1099 struct pci_dev *pdev = NULL;
1102 dev_set_drvdata(gendev, dev);
1104 /* Ensure we're not sleeping */
1105 if (lp->bus == EISA) {
1106 outb(WAKEUP, PCI_CFPM);
1108 pdev = to_pci_dev (gendev);
1109 pci_write_config_byte(pdev, PCI_CFDA_PSM, WAKEUP);
1115 if ((inl(DE4X5_STS) & (STS_TS | STS_RS)) != 0) {
1116 return -ENXIO; /* Hardware could not reset */
1120 ** Now find out what kind of DC21040/DC21041/DC21140 board we have.
1122 lp->useSROM = false;
1123 if (lp->bus == PCI) {
1124 PCI_signature(name, lp);
1126 EISA_signature(name, gendev);
1129 if (*name == '\0') { /* Not found a board signature */
1133 dev->base_addr = iobase;
1134 printk ("%s: %s at 0x%04lx", dev_name(gendev), name, iobase);
1136 status = get_hw_addr(dev);
1137 printk(", h/w address %pM\n", dev->dev_addr);
1140 printk(" which has an Ethernet PROM CRC error.\n");
1143 skb_queue_head_init(&lp->cache.queue);
1144 lp->cache.gepc = GEP_INIT;
1145 lp->asBit = GEP_SLNK;
1146 lp->asPolarity = GEP_SLNK;
1147 lp->asBitValid = ~0;
1149 lp->gendev = gendev;
1150 spin_lock_init(&lp->lock);
1151 init_timer(&lp->timer);
1152 lp->timer.function = (void (*)(unsigned long))de4x5_ast;
1153 lp->timer.data = (unsigned long)dev;
1154 de4x5_parse_params(dev);
1157 ** Choose correct autosensing in case someone messed up
1159 lp->autosense = lp->params.autosense;
1160 if (lp->chipset != DC21140) {
1161 if ((lp->chipset==DC21040) && (lp->params.autosense&TP_NW)) {
1162 lp->params.autosense = TP;
1164 if ((lp->chipset==DC21041) && (lp->params.autosense&BNC_AUI)) {
1165 lp->params.autosense = BNC;
1168 lp->fdx = lp->params.fdx;
1169 sprintf(lp->adapter_name,"%s (%s)", name, dev_name(gendev));
1171 lp->dma_size = (NUM_RX_DESC + NUM_TX_DESC) * sizeof(struct de4x5_desc);
1172 #if defined(__alpha__) || defined(__powerpc__) || defined(CONFIG_SPARC) || defined(DE4X5_DO_MEMCPY)
1173 lp->dma_size += RX_BUFF_SZ * NUM_RX_DESC + DE4X5_ALIGN;
1175 lp->rx_ring = dma_alloc_coherent(gendev, lp->dma_size,
1176 &lp->dma_rings, GFP_ATOMIC);
1177 if (lp->rx_ring == NULL) {
1181 lp->tx_ring = lp->rx_ring + NUM_RX_DESC;
1184 ** Set up the RX descriptor ring (Intels)
1185 ** Allocate contiguous receive buffers, long word aligned (Alphas)
1187 #if !defined(__alpha__) && !defined(__powerpc__) && !defined(CONFIG_SPARC) && !defined(DE4X5_DO_MEMCPY)
1188 for (i=0; i<NUM_RX_DESC; i++) {
1189 lp->rx_ring[i].status = 0;
1190 lp->rx_ring[i].des1 = cpu_to_le32(RX_BUFF_SZ);
1191 lp->rx_ring[i].buf = 0;
1192 lp->rx_ring[i].next = 0;
1193 lp->rx_skb[i] = (struct sk_buff *) 1; /* Dummy entry */
1198 dma_addr_t dma_rx_bufs;
1200 dma_rx_bufs = lp->dma_rings + (NUM_RX_DESC + NUM_TX_DESC)
1201 * sizeof(struct de4x5_desc);
1202 dma_rx_bufs = (dma_rx_bufs + DE4X5_ALIGN) & ~DE4X5_ALIGN;
1203 lp->rx_bufs = (char *)(((long)(lp->rx_ring + NUM_RX_DESC
1204 + NUM_TX_DESC) + DE4X5_ALIGN) & ~DE4X5_ALIGN);
1205 for (i=0; i<NUM_RX_DESC; i++) {
1206 lp->rx_ring[i].status = 0;
1207 lp->rx_ring[i].des1 = cpu_to_le32(RX_BUFF_SZ);
1208 lp->rx_ring[i].buf =
1209 cpu_to_le32(dma_rx_bufs+i*RX_BUFF_SZ);
1210 lp->rx_ring[i].next = 0;
1211 lp->rx_skb[i] = (struct sk_buff *) 1; /* Dummy entry */
1219 lp->rxRingSize = NUM_RX_DESC;
1220 lp->txRingSize = NUM_TX_DESC;
1222 /* Write the end of list marker to the descriptor lists */
1223 lp->rx_ring[lp->rxRingSize - 1].des1 |= cpu_to_le32(RD_RER);
1224 lp->tx_ring[lp->txRingSize - 1].des1 |= cpu_to_le32(TD_TER);
1226 /* Tell the adapter where the TX/RX rings are located. */
1227 outl(lp->dma_rings, DE4X5_RRBA);
1228 outl(lp->dma_rings + NUM_RX_DESC * sizeof(struct de4x5_desc),
1231 /* Initialise the IRQ mask and Enable/Disable */
1232 lp->irq_mask = IMR_RIM | IMR_TIM | IMR_TUM | IMR_UNM;
1233 lp->irq_en = IMR_NIM | IMR_AIM;
1235 /* Create a loopback packet frame for later media probing */
1236 create_packet(dev, lp->frame, sizeof(lp->frame));
1238 /* Check if the RX overflow bug needs testing for */
1239 i = lp->cfrv & 0x000000fe;
1240 if ((lp->chipset == DC21140) && (i == 0x20)) {
1244 /* Initialise the SROM pointers if possible */
1246 lp->state = INITIALISED;
1247 if (srom_infoleaf_info(dev)) {
1248 dma_free_coherent (gendev, lp->dma_size,
1249 lp->rx_ring, lp->dma_rings);
1258 ** Check for an MII interface
1260 if ((lp->chipset != DC21040) && (lp->chipset != DC21041)) {
1264 printk(" and requires IRQ%d (provided by %s).\n", dev->irq,
1265 ((lp->bus == PCI) ? "PCI BIOS" : "EISA CNFG"));
1268 if (de4x5_debug & DEBUG_VERSION) {
1272 /* The DE4X5-specific entries in the device structure. */
1273 SET_NETDEV_DEV(dev, gendev);
1274 dev->netdev_ops = &de4x5_netdev_ops;
1277 /* Fill in the generic fields of the device structure. */
1278 if ((status = register_netdev (dev))) {
1279 dma_free_coherent (gendev, lp->dma_size,
1280 lp->rx_ring, lp->dma_rings);
1284 /* Let the adapter sleep to save power */
1292 de4x5_open(struct net_device *dev)
1294 struct de4x5_private *lp = netdev_priv(dev);
1295 u_long iobase = dev->base_addr;
1299 /* Allocate the RX buffers */
1300 for (i=0; i<lp->rxRingSize; i++) {
1301 if (de4x5_alloc_rx_buff(dev, i, 0) == NULL) {
1302 de4x5_free_rx_buffs(dev);
1308 ** Wake up the adapter
1313 ** Re-initialize the DE4X5...
1315 status = de4x5_init(dev);
1316 spin_lock_init(&lp->lock);
1318 de4x5_dbg_open(dev);
1320 if (request_irq(dev->irq, de4x5_interrupt, IRQF_SHARED,
1321 lp->adapter_name, dev)) {
1322 printk("de4x5_open(): Requested IRQ%d is busy - attemping FAST/SHARE...", dev->irq);
1323 if (request_irq(dev->irq, de4x5_interrupt, IRQF_SHARED,
1324 lp->adapter_name, dev)) {
1325 printk("\n Cannot get IRQ- reconfigure your hardware.\n");
1327 de4x5_free_rx_buffs(dev);
1328 de4x5_free_tx_buffs(dev);
1333 printk("\n Succeeded, but you should reconfigure your hardware to avoid this.\n");
1334 printk("WARNING: there may be IRQ related problems in heavily loaded systems.\n");
1338 lp->interrupt = UNMASK_INTERRUPTS;
1339 dev->trans_start = jiffies; /* prevent tx timeout */
1343 de4x5_setup_intr(dev);
1345 if (de4x5_debug & DEBUG_OPEN) {
1346 printk("\tsts: 0x%08x\n", inl(DE4X5_STS));
1347 printk("\tbmr: 0x%08x\n", inl(DE4X5_BMR));
1348 printk("\timr: 0x%08x\n", inl(DE4X5_IMR));
1349 printk("\tomr: 0x%08x\n", inl(DE4X5_OMR));
1350 printk("\tsisr: 0x%08x\n", inl(DE4X5_SISR));
1351 printk("\tsicr: 0x%08x\n", inl(DE4X5_SICR));
1352 printk("\tstrr: 0x%08x\n", inl(DE4X5_STRR));
1353 printk("\tsigr: 0x%08x\n", inl(DE4X5_SIGR));
1360 ** Initialize the DE4X5 operating conditions. NB: a chip problem with the
1361 ** DC21140 requires using perfect filtering mode for that chip. Since I can't
1362 ** see why I'd want > 14 multicast addresses, I have changed all chips to use
1363 ** the perfect filtering mode. Keep the DMA burst length at 8: there seems
1364 ** to be data corruption problems if it is larger (UDP errors seen from a
1368 de4x5_init(struct net_device *dev)
1370 /* Lock out other processes whilst setting up the hardware */
1371 netif_stop_queue(dev);
1373 de4x5_sw_reset(dev);
1375 /* Autoconfigure the connected port */
1376 autoconf_media(dev);
1382 de4x5_sw_reset(struct net_device *dev)
1384 struct de4x5_private *lp = netdev_priv(dev);
1385 u_long iobase = dev->base_addr;
1386 int i, j, status = 0;
1389 /* Select the MII or SRL port now and RESET the MAC */
1391 if (lp->phy[lp->active].id != 0) {
1392 lp->infoblock_csr6 = OMR_SDP | OMR_PS | OMR_HBD;
1394 lp->infoblock_csr6 = OMR_SDP | OMR_TTM;
1396 de4x5_switch_mac_port(dev);
1400 ** Set the programmable burst length to 8 longwords for all the DC21140
1401 ** Fasternet chips and 4 longwords for all others: DMA errors result
1402 ** without these values. Cache align 16 long.
1404 bmr = (lp->chipset==DC21140 ? PBL_8 : PBL_4) | DESC_SKIP_LEN | DE4X5_CACHE_ALIGN;
1405 bmr |= ((lp->chipset & ~0x00ff)==DC2114x ? BMR_RML : 0);
1406 outl(bmr, DE4X5_BMR);
1408 omr = inl(DE4X5_OMR) & ~OMR_PR; /* Turn off promiscuous mode */
1409 if (lp->chipset == DC21140) {
1410 omr |= (OMR_SDP | OMR_SB);
1412 lp->setup_f = PERFECT;
1413 outl(lp->dma_rings, DE4X5_RRBA);
1414 outl(lp->dma_rings + NUM_RX_DESC * sizeof(struct de4x5_desc),
1417 lp->rx_new = lp->rx_old = 0;
1418 lp->tx_new = lp->tx_old = 0;
1420 for (i = 0; i < lp->rxRingSize; i++) {
1421 lp->rx_ring[i].status = cpu_to_le32(R_OWN);
1424 for (i = 0; i < lp->txRingSize; i++) {
1425 lp->tx_ring[i].status = cpu_to_le32(0);
1430 /* Build the setup frame depending on filtering mode */
1431 SetMulticastFilter(dev);
1433 load_packet(dev, lp->setup_frame, PERFECT_F|TD_SET|SETUP_FRAME_LEN, (struct sk_buff *)1);
1434 outl(omr|OMR_ST, DE4X5_OMR);
1436 /* Poll for setup frame completion (adapter interrupts are disabled now) */
1438 for (j=0, i=0;(i<500) && (j==0);i++) { /* Up to 500ms delay */
1440 if ((s32)le32_to_cpu(lp->tx_ring[lp->tx_new].status) >= 0) j=1;
1442 outl(omr, DE4X5_OMR); /* Stop everything! */
1445 printk("%s: Setup frame timed out, status %08x\n", dev->name,
1450 lp->tx_new = (lp->tx_new + 1) % lp->txRingSize;
1451 lp->tx_old = lp->tx_new;
1457 ** Writes a socket buffer address to the next available transmit descriptor.
1460 de4x5_queue_pkt(struct sk_buff *skb, struct net_device *dev)
1462 struct de4x5_private *lp = netdev_priv(dev);
1463 u_long iobase = dev->base_addr;
1466 netif_stop_queue(dev);
1467 if (!lp->tx_enable) /* Cannot send for now */
1468 return NETDEV_TX_LOCKED;
1471 ** Clean out the TX ring asynchronously to interrupts - sometimes the
1472 ** interrupts are lost by delayed descriptor status updates relative to
1473 ** the irq assertion, especially with a busy PCI bus.
1475 spin_lock_irqsave(&lp->lock, flags);
1477 spin_unlock_irqrestore(&lp->lock, flags);
1479 /* Test if cache is already locked - requeue skb if so */
1480 if (test_and_set_bit(0, (void *)&lp->cache.lock) && !lp->interrupt)
1481 return NETDEV_TX_LOCKED;
1483 /* Transmit descriptor ring full or stale skb */
1484 if (netif_queue_stopped(dev) || (u_long) lp->tx_skb[lp->tx_new] > 1) {
1485 if (lp->interrupt) {
1486 de4x5_putb_cache(dev, skb); /* Requeue the buffer */
1488 de4x5_put_cache(dev, skb);
1490 if (de4x5_debug & DEBUG_TX) {
1491 printk("%s: transmit busy, lost media or stale skb found:\n STS:%08x\n tbusy:%d\n IMR:%08x\n OMR:%08x\n Stale skb: %s\n",dev->name, inl(DE4X5_STS), netif_queue_stopped(dev), inl(DE4X5_IMR), inl(DE4X5_OMR), ((u_long) lp->tx_skb[lp->tx_new] > 1) ? "YES" : "NO");
1493 } else if (skb->len > 0) {
1494 /* If we already have stuff queued locally, use that first */
1495 if (!skb_queue_empty(&lp->cache.queue) && !lp->interrupt) {
1496 de4x5_put_cache(dev, skb);
1497 skb = de4x5_get_cache(dev);
1500 while (skb && !netif_queue_stopped(dev) &&
1501 (u_long) lp->tx_skb[lp->tx_new] <= 1) {
1502 spin_lock_irqsave(&lp->lock, flags);
1503 netif_stop_queue(dev);
1504 load_packet(dev, skb->data, TD_IC | TD_LS | TD_FS | skb->len, skb);
1505 lp->stats.tx_bytes += skb->len;
1506 outl(POLL_DEMAND, DE4X5_TPD);/* Start the TX */
1508 lp->tx_new = (lp->tx_new + 1) % lp->txRingSize;
1510 if (TX_BUFFS_AVAIL) {
1511 netif_start_queue(dev); /* Another pkt may be queued */
1513 skb = de4x5_get_cache(dev);
1514 spin_unlock_irqrestore(&lp->lock, flags);
1516 if (skb) de4x5_putb_cache(dev, skb);
1521 return NETDEV_TX_OK;
1525 ** The DE4X5 interrupt handler.
1527 ** I/O Read/Writes through intermediate PCI bridges are never 'posted',
1528 ** so that the asserted interrupt always has some real data to work with -
1529 ** if these I/O accesses are ever changed to memory accesses, ensure the
1530 ** STS write is read immediately to complete the transaction if the adapter
1531 ** is not on bus 0. Lost interrupts can still occur when the PCI bus load
1532 ** is high and descriptor status bits cannot be set before the associated
1533 ** interrupt is asserted and this routine entered.
1536 de4x5_interrupt(int irq, void *dev_id)
1538 struct net_device *dev = dev_id;
1539 struct de4x5_private *lp;
1540 s32 imr, omr, sts, limit;
1542 unsigned int handled = 0;
1544 lp = netdev_priv(dev);
1545 spin_lock(&lp->lock);
1546 iobase = dev->base_addr;
1548 DISABLE_IRQs; /* Ensure non re-entrancy */
1550 if (test_and_set_bit(MASK_INTERRUPTS, (void*) &lp->interrupt))
1551 printk("%s: Re-entering the interrupt handler.\n", dev->name);
1553 synchronize_irq(dev->irq);
1555 for (limit=0; limit<8; limit++) {
1556 sts = inl(DE4X5_STS); /* Read IRQ status */
1557 outl(sts, DE4X5_STS); /* Reset the board interrupts */
1559 if (!(sts & lp->irq_mask)) break;/* All done */
1562 if (sts & (STS_RI | STS_RU)) /* Rx interrupt (packet[s] arrived) */
1565 if (sts & (STS_TI | STS_TU)) /* Tx interrupt (packet sent) */
1568 if (sts & STS_LNF) { /* TP Link has failed */
1569 lp->irq_mask &= ~IMR_LFM;
1572 if (sts & STS_UNF) { /* Transmit underrun */
1576 if (sts & STS_SE) { /* Bus Error */
1578 printk("%s: Fatal bus error occurred, sts=%#8x, device stopped.\n",
1580 spin_unlock(&lp->lock);
1585 /* Load the TX ring with any locally stored packets */
1586 if (!test_and_set_bit(0, (void *)&lp->cache.lock)) {
1587 while (!skb_queue_empty(&lp->cache.queue) && !netif_queue_stopped(dev) && lp->tx_enable) {
1588 de4x5_queue_pkt(de4x5_get_cache(dev), dev);
1593 lp->interrupt = UNMASK_INTERRUPTS;
1595 spin_unlock(&lp->lock);
1597 return IRQ_RETVAL(handled);
1601 de4x5_rx(struct net_device *dev)
1603 struct de4x5_private *lp = netdev_priv(dev);
1604 u_long iobase = dev->base_addr;
1608 for (entry=lp->rx_new; (s32)le32_to_cpu(lp->rx_ring[entry].status)>=0;
1610 status = (s32)le32_to_cpu(lp->rx_ring[entry].status);
1613 if (inl(DE4X5_MFC) & MFC_FOCM) {
1619 if (status & RD_FS) { /* Remember the start of frame */
1623 if (status & RD_LS) { /* Valid frame status */
1624 if (lp->tx_enable) lp->linkOK++;
1625 if (status & RD_ES) { /* There was an error. */
1626 lp->stats.rx_errors++; /* Update the error stats. */
1627 if (status & (RD_RF | RD_TL)) lp->stats.rx_frame_errors++;
1628 if (status & RD_CE) lp->stats.rx_crc_errors++;
1629 if (status & RD_OF) lp->stats.rx_fifo_errors++;
1630 if (status & RD_TL) lp->stats.rx_length_errors++;
1631 if (status & RD_RF) lp->pktStats.rx_runt_frames++;
1632 if (status & RD_CS) lp->pktStats.rx_collision++;
1633 if (status & RD_DB) lp->pktStats.rx_dribble++;
1634 if (status & RD_OF) lp->pktStats.rx_overflow++;
1635 } else { /* A valid frame received */
1636 struct sk_buff *skb;
1637 short pkt_len = (short)(le32_to_cpu(lp->rx_ring[entry].status)
1640 if ((skb = de4x5_alloc_rx_buff(dev, entry, pkt_len)) == NULL) {
1641 printk("%s: Insufficient memory; nuking packet.\n",
1643 lp->stats.rx_dropped++;
1645 de4x5_dbg_rx(skb, pkt_len);
1647 /* Push up the protocol stack */
1648 skb->protocol=eth_type_trans(skb,dev);
1649 de4x5_local_stats(dev, skb->data, pkt_len);
1653 lp->stats.rx_packets++;
1654 lp->stats.rx_bytes += pkt_len;
1658 /* Change buffer ownership for this frame, back to the adapter */
1659 for (;lp->rx_old!=entry;lp->rx_old=(lp->rx_old + 1)%lp->rxRingSize) {
1660 lp->rx_ring[lp->rx_old].status = cpu_to_le32(R_OWN);
1663 lp->rx_ring[entry].status = cpu_to_le32(R_OWN);
1668 ** Update entry information
1670 lp->rx_new = (lp->rx_new + 1) % lp->rxRingSize;
1677 de4x5_free_tx_buff(struct de4x5_private *lp, int entry)
1679 dma_unmap_single(lp->gendev, le32_to_cpu(lp->tx_ring[entry].buf),
1680 le32_to_cpu(lp->tx_ring[entry].des1) & TD_TBS1,
1682 if ((u_long) lp->tx_skb[entry] > 1)
1683 dev_kfree_skb_irq(lp->tx_skb[entry]);
1684 lp->tx_skb[entry] = NULL;
1688 ** Buffer sent - check for TX buffer errors.
1691 de4x5_tx(struct net_device *dev)
1693 struct de4x5_private *lp = netdev_priv(dev);
1694 u_long iobase = dev->base_addr;
1698 for (entry = lp->tx_old; entry != lp->tx_new; entry = lp->tx_old) {
1699 status = (s32)le32_to_cpu(lp->tx_ring[entry].status);
1700 if (status < 0) { /* Buffer not sent yet */
1702 } else if (status != 0x7fffffff) { /* Not setup frame */
1703 if (status & TD_ES) { /* An error happened */
1704 lp->stats.tx_errors++;
1705 if (status & TD_NC) lp->stats.tx_carrier_errors++;
1706 if (status & TD_LC) lp->stats.tx_window_errors++;
1707 if (status & TD_UF) lp->stats.tx_fifo_errors++;
1708 if (status & TD_EC) lp->pktStats.excessive_collisions++;
1709 if (status & TD_DE) lp->stats.tx_aborted_errors++;
1711 if (TX_PKT_PENDING) {
1712 outl(POLL_DEMAND, DE4X5_TPD);/* Restart a stalled TX */
1714 } else { /* Packet sent */
1715 lp->stats.tx_packets++;
1716 if (lp->tx_enable) lp->linkOK++;
1718 /* Update the collision counter */
1719 lp->stats.collisions += ((status & TD_EC) ? 16 :
1720 ((status & TD_CC) >> 3));
1722 /* Free the buffer. */
1723 if (lp->tx_skb[entry] != NULL)
1724 de4x5_free_tx_buff(lp, entry);
1727 /* Update all the pointers */
1728 lp->tx_old = (lp->tx_old + 1) % lp->txRingSize;
1731 /* Any resources available? */
1732 if (TX_BUFFS_AVAIL && netif_queue_stopped(dev)) {
1734 netif_wake_queue(dev);
1736 netif_start_queue(dev);
1743 de4x5_ast(struct net_device *dev)
1745 struct de4x5_private *lp = netdev_priv(dev);
1746 int next_tick = DE4X5_AUTOSENSE_MS;
1750 next_tick = srom_autoconf(dev);
1751 else if (lp->chipset == DC21140)
1752 next_tick = dc21140m_autoconf(dev);
1753 else if (lp->chipset == DC21041)
1754 next_tick = dc21041_autoconf(dev);
1755 else if (lp->chipset == DC21040)
1756 next_tick = dc21040_autoconf(dev);
1759 dt = (next_tick * HZ) / 1000;
1764 mod_timer(&lp->timer, jiffies + dt);
1768 de4x5_txur(struct net_device *dev)
1770 struct de4x5_private *lp = netdev_priv(dev);
1771 u_long iobase = dev->base_addr;
1774 omr = inl(DE4X5_OMR);
1775 if (!(omr & OMR_SF) || (lp->chipset==DC21041) || (lp->chipset==DC21040)) {
1776 omr &= ~(OMR_ST|OMR_SR);
1777 outl(omr, DE4X5_OMR);
1778 while (inl(DE4X5_STS) & STS_TS);
1779 if ((omr & OMR_TR) < OMR_TR) {
1784 outl(omr | OMR_ST | OMR_SR, DE4X5_OMR);
1791 de4x5_rx_ovfc(struct net_device *dev)
1793 struct de4x5_private *lp = netdev_priv(dev);
1794 u_long iobase = dev->base_addr;
1797 omr = inl(DE4X5_OMR);
1798 outl(omr & ~OMR_SR, DE4X5_OMR);
1799 while (inl(DE4X5_STS) & STS_RS);
1801 for (; (s32)le32_to_cpu(lp->rx_ring[lp->rx_new].status)>=0;) {
1802 lp->rx_ring[lp->rx_new].status = cpu_to_le32(R_OWN);
1803 lp->rx_new = (lp->rx_new + 1) % lp->rxRingSize;
1806 outl(omr, DE4X5_OMR);
1812 de4x5_close(struct net_device *dev)
1814 struct de4x5_private *lp = netdev_priv(dev);
1815 u_long iobase = dev->base_addr;
1820 netif_stop_queue(dev);
1822 if (de4x5_debug & DEBUG_CLOSE) {
1823 printk("%s: Shutting down ethercard, status was %8.8x.\n",
1824 dev->name, inl(DE4X5_STS));
1828 ** We stop the DE4X5 here... mask interrupts and stop TX & RX
1833 /* Free the associated irq */
1834 free_irq(dev->irq, dev);
1837 /* Free any socket buffers */
1838 de4x5_free_rx_buffs(dev);
1839 de4x5_free_tx_buffs(dev);
1841 /* Put the adapter to sleep to save power */
1847 static struct net_device_stats *
1848 de4x5_get_stats(struct net_device *dev)
1850 struct de4x5_private *lp = netdev_priv(dev);
1851 u_long iobase = dev->base_addr;
1853 lp->stats.rx_missed_errors = (int)(inl(DE4X5_MFC) & (MFC_OVFL | MFC_CNTR));
1859 de4x5_local_stats(struct net_device *dev, char *buf, int pkt_len)
1861 struct de4x5_private *lp = netdev_priv(dev);
1864 for (i=1; i<DE4X5_PKT_STAT_SZ-1; i++) {
1865 if (pkt_len < (i*DE4X5_PKT_BIN_SZ)) {
1866 lp->pktStats.bins[i]++;
1867 i = DE4X5_PKT_STAT_SZ;
1870 if (is_multicast_ether_addr(buf)) {
1871 if (is_broadcast_ether_addr(buf)) {
1872 lp->pktStats.broadcast++;
1874 lp->pktStats.multicast++;
1876 } else if (ether_addr_equal(buf, dev->dev_addr)) {
1877 lp->pktStats.unicast++;
1880 lp->pktStats.bins[0]++; /* Duplicates stats.rx_packets */
1881 if (lp->pktStats.bins[0] == 0) { /* Reset counters */
1882 memset((char *)&lp->pktStats, 0, sizeof(lp->pktStats));
1887 ** Removes the TD_IC flag from previous descriptor to improve TX performance.
1888 ** If the flag is changed on a descriptor that is being read by the hardware,
1889 ** I assume PCI transaction ordering will mean you are either successful or
1890 ** just miss asserting the change to the hardware. Anyway you're messing with
1891 ** a descriptor you don't own, but this shouldn't kill the chip provided
1892 ** the descriptor register is read only to the hardware.
1895 load_packet(struct net_device *dev, char *buf, u32 flags, struct sk_buff *skb)
1897 struct de4x5_private *lp = netdev_priv(dev);
1898 int entry = (lp->tx_new ? lp->tx_new-1 : lp->txRingSize-1);
1899 dma_addr_t buf_dma = dma_map_single(lp->gendev, buf, flags & TD_TBS1, DMA_TO_DEVICE);
1901 lp->tx_ring[lp->tx_new].buf = cpu_to_le32(buf_dma);
1902 lp->tx_ring[lp->tx_new].des1 &= cpu_to_le32(TD_TER);
1903 lp->tx_ring[lp->tx_new].des1 |= cpu_to_le32(flags);
1904 lp->tx_skb[lp->tx_new] = skb;
1905 lp->tx_ring[entry].des1 &= cpu_to_le32(~TD_IC);
1908 lp->tx_ring[lp->tx_new].status = cpu_to_le32(T_OWN);
1913 ** Set or clear the multicast filter for this adaptor.
1916 set_multicast_list(struct net_device *dev)
1918 struct de4x5_private *lp = netdev_priv(dev);
1919 u_long iobase = dev->base_addr;
1921 /* First, double check that the adapter is open */
1922 if (lp->state == OPEN) {
1923 if (dev->flags & IFF_PROMISC) { /* set promiscuous mode */
1925 omr = inl(DE4X5_OMR);
1927 outl(omr, DE4X5_OMR);
1929 SetMulticastFilter(dev);
1930 load_packet(dev, lp->setup_frame, TD_IC | PERFECT_F | TD_SET |
1931 SETUP_FRAME_LEN, (struct sk_buff *)1);
1933 lp->tx_new = (lp->tx_new + 1) % lp->txRingSize;
1934 outl(POLL_DEMAND, DE4X5_TPD); /* Start the TX */
1935 dev->trans_start = jiffies; /* prevent tx timeout */
1941 ** Calculate the hash code and update the logical address filter
1942 ** from a list of ethernet multicast addresses.
1943 ** Little endian crc one liner from Matt Thomas, DEC.
1946 SetMulticastFilter(struct net_device *dev)
1948 struct de4x5_private *lp = netdev_priv(dev);
1949 struct netdev_hw_addr *ha;
1950 u_long iobase = dev->base_addr;
1955 unsigned char *addrs;
1957 omr = inl(DE4X5_OMR);
1958 omr &= ~(OMR_PR | OMR_PM);
1959 pa = build_setup_frame(dev, ALL); /* Build the basic frame */
1961 if ((dev->flags & IFF_ALLMULTI) || (netdev_mc_count(dev) > 14)) {
1962 omr |= OMR_PM; /* Pass all multicasts */
1963 } else if (lp->setup_f == HASH_PERF) { /* Hash Filtering */
1964 netdev_for_each_mc_addr(ha, dev) {
1965 crc = ether_crc_le(ETH_ALEN, ha->addr);
1966 hashcode = crc & HASH_BITS; /* hashcode is 9 LSb of CRC */
1968 byte = hashcode >> 3; /* bit[3-8] -> byte in filter */
1969 bit = 1 << (hashcode & 0x07);/* bit[0-2] -> bit in byte */
1971 byte <<= 1; /* calc offset into setup frame */
1975 lp->setup_frame[byte] |= bit;
1977 } else { /* Perfect filtering */
1978 netdev_for_each_mc_addr(ha, dev) {
1980 for (i=0; i<ETH_ALEN; i++) {
1981 *(pa + (i&1)) = *addrs++;
1982 if (i & 0x01) pa += 4;
1986 outl(omr, DE4X5_OMR);
1991 static u_char de4x5_irq[] = EISA_ALLOWED_IRQ_LIST;
1993 static int de4x5_eisa_probe(struct device *gendev)
1995 struct eisa_device *edev;
2001 struct net_device *dev;
2002 struct de4x5_private *lp;
2004 edev = to_eisa_device (gendev);
2005 iobase = edev->base_addr;
2007 if (!request_region (iobase, DE4X5_EISA_TOTAL_SIZE, "de4x5"))
2010 if (!request_region (iobase + DE4X5_EISA_IO_PORTS,
2011 DE4X5_EISA_TOTAL_SIZE, "de4x5")) {
2016 if (!(dev = alloc_etherdev (sizeof (struct de4x5_private)))) {
2020 lp = netdev_priv(dev);
2022 cfid = (u32) inl(PCI_CFID);
2023 lp->cfrv = (u_short) inl(PCI_CFRV);
2024 device = (cfid >> 8) & 0x00ffff00;
2025 vendor = (u_short) cfid;
2027 /* Read the EISA Configuration Registers */
2028 regval = inb(EISA_REG0) & (ER0_INTL | ER0_INTT);
2030 /* Looks like the Jensen firmware (rev 2.2) doesn't really
2031 * care about the EISA configuration, and thus doesn't
2032 * configure the PLX bridge properly. Oh well... Simply mimic
2033 * the EISA config file to sort it out. */
2035 /* EISA REG1: Assert DecChip 21040 HW Reset */
2036 outb (ER1_IAM | 1, EISA_REG1);
2039 /* EISA REG1: Deassert DecChip 21040 HW Reset */
2040 outb (ER1_IAM, EISA_REG1);
2043 /* EISA REG3: R/W Burst Transfer Enable */
2044 outb (ER3_BWE | ER3_BRE, EISA_REG3);
2046 /* 32_bit slave/master, Preempt Time=23 bclks, Unlatched Interrupt */
2047 outb (ER0_BSW | ER0_BMW | ER0_EPT | regval, EISA_REG0);
2049 irq = de4x5_irq[(regval >> 1) & 0x03];
2052 device = ((lp->cfrv & CFRV_RN) < DC2114x_BRK ? DC21142 : DC21143);
2054 lp->chipset = device;
2057 /* Write the PCI Configuration Registers */
2058 outl(PCI_COMMAND_IO | PCI_COMMAND_MASTER, PCI_CFCS);
2059 outl(0x00006000, PCI_CFLT);
2060 outl(iobase, PCI_CBIO);
2062 DevicePresent(dev, EISA_APROM);
2066 if (!(status = de4x5_hw_init (dev, iobase, gendev))) {
2072 release_region (iobase + DE4X5_EISA_IO_PORTS, DE4X5_EISA_TOTAL_SIZE);
2074 release_region (iobase, DE4X5_EISA_TOTAL_SIZE);
2079 static int de4x5_eisa_remove(struct device *device)
2081 struct net_device *dev;
2084 dev = dev_get_drvdata(device);
2085 iobase = dev->base_addr;
2087 unregister_netdev (dev);
2089 release_region (iobase + DE4X5_EISA_IO_PORTS, DE4X5_EISA_TOTAL_SIZE);
2090 release_region (iobase, DE4X5_EISA_TOTAL_SIZE);
2095 static struct eisa_device_id de4x5_eisa_ids[] = {
2096 { "DEC4250", 0 }, /* 0 is the board name index... */
2099 MODULE_DEVICE_TABLE(eisa, de4x5_eisa_ids);
2101 static struct eisa_driver de4x5_eisa_driver = {
2102 .id_table = de4x5_eisa_ids,
2105 .probe = de4x5_eisa_probe,
2106 .remove = de4x5_eisa_remove,
2114 ** This function searches the current bus (which is >0) for a DECchip with an
2115 ** SROM, so that in multiport cards that have one SROM shared between multiple
2116 ** DECchips, we can find the base SROM irrespective of the BIOS scan direction.
2117 ** For single port cards this is a time waster...
2120 srom_search(struct net_device *dev, struct pci_dev *pdev)
2123 u_short vendor, status;
2124 u_int irq = 0, device;
2125 u_long iobase = 0; /* Clear upper 32 bits in Alphas */
2127 struct de4x5_private *lp = netdev_priv(dev);
2128 struct pci_dev *this_dev;
2130 list_for_each_entry(this_dev, &pdev->bus->devices, bus_list) {
2131 vendor = this_dev->vendor;
2132 device = this_dev->device << 8;
2133 if (!(is_DC21040 || is_DC21041 || is_DC21140 || is_DC2114x)) continue;
2135 /* Get the chip configuration revision register */
2136 pb = this_dev->bus->number;
2138 /* Set the device number information */
2139 lp->device = PCI_SLOT(this_dev->devfn);
2142 /* Set the chipset information */
2144 device = ((this_dev->revision & CFRV_RN) < DC2114x_BRK
2145 ? DC21142 : DC21143);
2147 lp->chipset = device;
2149 /* Get the board I/O address (64 bits on sparc64) */
2150 iobase = pci_resource_start(this_dev, 0);
2152 /* Fetch the IRQ to be used */
2153 irq = this_dev->irq;
2154 if ((irq == 0) || (irq == 0xff) || ((int)irq == -1)) continue;
2156 /* Check if I/O accesses are enabled */
2157 pci_read_config_word(this_dev, PCI_COMMAND, &status);
2158 if (!(status & PCI_COMMAND_IO)) continue;
2160 /* Search for a valid SROM attached to this DECchip */
2161 DevicePresent(dev, DE4X5_APROM);
2162 for (j=0, i=0; i<ETH_ALEN; i++) {
2163 j += (u_char) *((u_char *)&lp->srom + SROM_HWADD + i);
2165 if (j != 0 && j != 6 * 0xff) {
2166 last.chipset = device;
2169 for (i=0; i<ETH_ALEN; i++) {
2170 last.addr[i] = (u_char)*((u_char *)&lp->srom + SROM_HWADD + i);
2178 ** PCI bus I/O device probe
2179 ** NB: PCI I/O accesses and Bus Mastering are enabled by the PCI BIOS, not
2180 ** the driver. Some PCI BIOS's, pre V2.1, need the slot + features to be
2181 ** enabled by the user first in the set up utility. Hence we just check for
2182 ** enabled features and silently ignore the card if they're not.
2184 ** STOP PRESS: Some BIOS's __require__ the driver to enable the bus mastering
2185 ** bit. Here, check for I/O accesses and then set BM. If you put the card in
2186 ** a non BM slot, you're on your own (and complain to the PC vendor that your
2187 ** PC doesn't conform to the PCI standard)!
2189 ** This function is only compatible with the *latest* 2.1.x kernels. For 2.0.x
2190 ** kernels use the V0.535[n] drivers.
2193 static int de4x5_pci_probe(struct pci_dev *pdev,
2194 const struct pci_device_id *ent)
2196 u_char pb, pbus = 0, dev_num, dnum = 0, timer;
2197 u_short vendor, status;
2198 u_int irq = 0, device;
2199 u_long iobase = 0; /* Clear upper 32 bits in Alphas */
2201 struct net_device *dev;
2202 struct de4x5_private *lp;
2204 dev_num = PCI_SLOT(pdev->devfn);
2205 pb = pdev->bus->number;
2207 if (io) { /* probe a single PCI device */
2208 pbus = (u_short)(io >> 8);
2209 dnum = (u_short)(io & 0xff);
2210 if ((pbus != pb) || (dnum != dev_num))
2214 vendor = pdev->vendor;
2215 device = pdev->device << 8;
2216 if (!(is_DC21040 || is_DC21041 || is_DC21140 || is_DC2114x))
2219 /* Ok, the device seems to be for us. */
2220 if ((error = pci_enable_device (pdev)))
2223 if (!(dev = alloc_etherdev (sizeof (struct de4x5_private)))) {
2228 lp = netdev_priv(dev);
2232 /* Search for an SROM on this bus */
2233 if (lp->bus_num != pb) {
2235 srom_search(dev, pdev);
2238 /* Get the chip configuration revision register */
2239 lp->cfrv = pdev->revision;
2241 /* Set the device number information */
2242 lp->device = dev_num;
2245 /* Set the chipset information */
2247 device = ((lp->cfrv & CFRV_RN) < DC2114x_BRK ? DC21142 : DC21143);
2249 lp->chipset = device;
2251 /* Get the board I/O address (64 bits on sparc64) */
2252 iobase = pci_resource_start(pdev, 0);
2254 /* Fetch the IRQ to be used */
2256 if ((irq == 0) || (irq == 0xff) || ((int)irq == -1)) {
2261 /* Check if I/O accesses and Bus Mastering are enabled */
2262 pci_read_config_word(pdev, PCI_COMMAND, &status);
2264 if (!(status & PCI_COMMAND_IO)) {
2265 status |= PCI_COMMAND_IO;
2266 pci_write_config_word(pdev, PCI_COMMAND, status);
2267 pci_read_config_word(pdev, PCI_COMMAND, &status);
2269 #endif /* __powerpc__ */
2270 if (!(status & PCI_COMMAND_IO)) {
2275 if (!(status & PCI_COMMAND_MASTER)) {
2276 status |= PCI_COMMAND_MASTER;
2277 pci_write_config_word(pdev, PCI_COMMAND, status);
2278 pci_read_config_word(pdev, PCI_COMMAND, &status);
2280 if (!(status & PCI_COMMAND_MASTER)) {
2285 /* Check the latency timer for values >= 0x60 */
2286 pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &timer);
2288 pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x60);
2291 DevicePresent(dev, DE4X5_APROM);
2293 if (!request_region (iobase, DE4X5_PCI_TOTAL_SIZE, "de4x5")) {
2300 if ((error = de4x5_hw_init(dev, iobase, &pdev->dev))) {
2307 release_region (iobase, DE4X5_PCI_TOTAL_SIZE);
2311 pci_disable_device (pdev);
2315 static void de4x5_pci_remove(struct pci_dev *pdev)
2317 struct net_device *dev;
2320 dev = pci_get_drvdata(pdev);
2321 iobase = dev->base_addr;
2323 unregister_netdev (dev);
2325 release_region (iobase, DE4X5_PCI_TOTAL_SIZE);
2326 pci_disable_device (pdev);
2329 static const struct pci_device_id de4x5_pci_tbl[] = {
2330 { PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_TULIP,
2331 PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
2332 { PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_TULIP_PLUS,
2333 PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1 },
2334 { PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_TULIP_FAST,
2335 PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2 },
2336 { PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_21142,
2337 PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3 },
2341 static struct pci_driver de4x5_pci_driver = {
2343 .id_table = de4x5_pci_tbl,
2344 .probe = de4x5_pci_probe,
2345 .remove = de4x5_pci_remove,
2351 ** Auto configure the media here rather than setting the port at compile
2352 ** time. This routine is called by de4x5_init() and when a loss of media is
2353 ** detected (excessive collisions, loss of carrier, no carrier or link fail
2354 ** [TP] or no recent receive activity) to check whether the user has been
2355 ** sneaky and changed the port on us.
2358 autoconf_media(struct net_device *dev)
2360 struct de4x5_private *lp = netdev_priv(dev);
2361 u_long iobase = dev->base_addr;
2365 lp->c_media = AUTO; /* Bogus last media */
2366 inl(DE4X5_MFC); /* Zero the lost frames counter */
2376 ** Autoconfigure the media when using the DC21040. AUI cannot be distinguished
2377 ** from BNC as the port has a jumper to set thick or thin wire. When set for
2378 ** BNC, the BNC port will indicate activity if it's not terminated correctly.
2379 ** The only way to test for that is to place a loopback packet onto the
2380 ** network and watch for errors. Since we're messing with the interrupt mask
2381 ** register, disable the board interrupts and do not allow any more packets to
2382 ** be queued to the hardware. Re-enable everything only when the media is
2384 ** I may have to "age out" locally queued packets so that the higher layer
2385 ** timeouts don't effectively duplicate packets on the network.
2388 dc21040_autoconf(struct net_device *dev)
2390 struct de4x5_private *lp = netdev_priv(dev);
2391 u_long iobase = dev->base_addr;
2392 int next_tick = DE4X5_AUTOSENSE_MS;
2395 switch (lp->media) {
2398 lp->tx_enable = false;
2400 de4x5_save_skbs(dev);
2401 if ((lp->autosense == AUTO) || (lp->autosense == TP)) {
2403 } else if ((lp->autosense == BNC) || (lp->autosense == AUI) || (lp->autosense == BNC_AUI)) {
2404 lp->media = BNC_AUI;
2405 } else if (lp->autosense == EXT_SIA) {
2406 lp->media = EXT_SIA;
2410 lp->local_state = 0;
2411 next_tick = dc21040_autoconf(dev);
2415 next_tick = dc21040_state(dev, 0x8f01, 0xffff, 0x0000, 3000, BNC_AUI,
2416 TP_SUSPECT, test_tp);
2420 next_tick = de4x5_suspect_state(dev, 1000, TP, test_tp, dc21040_autoconf);
2426 next_tick = dc21040_state(dev, 0x8f09, 0x0705, 0x0006, 3000, EXT_SIA,
2427 BNC_AUI_SUSPECT, ping_media);
2430 case BNC_AUI_SUSPECT:
2431 next_tick = de4x5_suspect_state(dev, 1000, BNC_AUI, ping_media, dc21040_autoconf);
2435 next_tick = dc21040_state(dev, 0x3041, 0x0000, 0x0006, 3000,
2436 NC, EXT_SIA_SUSPECT, ping_media);
2439 case EXT_SIA_SUSPECT:
2440 next_tick = de4x5_suspect_state(dev, 1000, EXT_SIA, ping_media, dc21040_autoconf);
2444 /* default to TP for all */
2445 reset_init_sia(dev, 0x8f01, 0xffff, 0x0000);
2446 if (lp->media != lp->c_media) {
2447 de4x5_dbg_media(dev);
2448 lp->c_media = lp->media;
2451 lp->tx_enable = false;
2459 dc21040_state(struct net_device *dev, int csr13, int csr14, int csr15, int timeout,
2460 int next_state, int suspect_state,
2461 int (*fn)(struct net_device *, int))
2463 struct de4x5_private *lp = netdev_priv(dev);
2464 int next_tick = DE4X5_AUTOSENSE_MS;
2467 switch (lp->local_state) {
2469 reset_init_sia(dev, csr13, csr14, csr15);
2475 if (!lp->tx_enable) {
2476 linkBad = fn(dev, timeout);
2478 next_tick = linkBad & ~TIMER_CB;
2480 if (linkBad && (lp->autosense == AUTO)) {
2481 lp->local_state = 0;
2482 lp->media = next_state;
2484 de4x5_init_connection(dev);
2487 } else if (!lp->linkOK && (lp->autosense == AUTO)) {
2488 lp->media = suspect_state;
2498 de4x5_suspect_state(struct net_device *dev, int timeout, int prev_state,
2499 int (*fn)(struct net_device *, int),
2500 int (*asfn)(struct net_device *))
2502 struct de4x5_private *lp = netdev_priv(dev);
2503 int next_tick = DE4X5_AUTOSENSE_MS;
2506 switch (lp->local_state) {
2509 lp->media = prev_state;
2512 next_tick = asfn(dev);
2517 linkBad = fn(dev, timeout);
2519 next_tick = linkBad & ~TIMER_CB;
2520 } else if (!linkBad) {
2522 lp->media = prev_state;
2533 ** Autoconfigure the media when using the DC21041. AUI needs to be tested
2534 ** before BNC, because the BNC port will indicate activity if it's not
2535 ** terminated correctly. The only way to test for that is to place a loopback
2536 ** packet onto the network and watch for errors. Since we're messing with
2537 ** the interrupt mask register, disable the board interrupts and do not allow
2538 ** any more packets to be queued to the hardware. Re-enable everything only
2539 ** when the media is found.
2542 dc21041_autoconf(struct net_device *dev)
2544 struct de4x5_private *lp = netdev_priv(dev);
2545 u_long iobase = dev->base_addr;
2546 s32 sts, irqs, irq_mask, imr, omr;
2547 int next_tick = DE4X5_AUTOSENSE_MS;
2549 switch (lp->media) {
2552 lp->tx_enable = false;
2554 de4x5_save_skbs(dev); /* Save non transmitted skb's */
2555 if ((lp->autosense == AUTO) || (lp->autosense == TP_NW)) {
2556 lp->media = TP; /* On chip auto negotiation is broken */
2557 } else if (lp->autosense == TP) {
2559 } else if (lp->autosense == BNC) {
2561 } else if (lp->autosense == AUI) {
2566 lp->local_state = 0;
2567 next_tick = dc21041_autoconf(dev);
2571 if (lp->timeout < 0) {
2572 omr = inl(DE4X5_OMR);/* Set up full duplex for the autonegotiate */
2573 outl(omr | OMR_FDX, DE4X5_OMR);
2575 irqs = STS_LNF | STS_LNP;
2576 irq_mask = IMR_LFM | IMR_LPM;
2577 sts = test_media(dev, irqs, irq_mask, 0xef01, 0xffff, 0x0008, 2400);
2579 next_tick = sts & ~TIMER_CB;
2581 if (sts & STS_LNP) {
2586 next_tick = dc21041_autoconf(dev);
2591 if (!lp->tx_enable) {
2594 sts = test_ans(dev, irqs, irq_mask, 3000);
2596 next_tick = sts & ~TIMER_CB;
2598 if (!(sts & STS_LNP) && (lp->autosense == AUTO)) {
2600 next_tick = dc21041_autoconf(dev);
2602 lp->local_state = 1;
2603 de4x5_init_connection(dev);
2606 } else if (!lp->linkOK && (lp->autosense == AUTO)) {
2607 lp->media = ANS_SUSPECT;
2613 next_tick = de4x5_suspect_state(dev, 1000, ANS, test_tp, dc21041_autoconf);
2617 if (!lp->tx_enable) {
2618 if (lp->timeout < 0) {
2619 omr = inl(DE4X5_OMR); /* Set up half duplex for TP */
2620 outl(omr & ~OMR_FDX, DE4X5_OMR);
2622 irqs = STS_LNF | STS_LNP;
2623 irq_mask = IMR_LFM | IMR_LPM;
2624 sts = test_media(dev,irqs, irq_mask, 0xef01, 0xff3f, 0x0008, 2400);
2626 next_tick = sts & ~TIMER_CB;
2628 if (!(sts & STS_LNP) && (lp->autosense == AUTO)) {
2629 if (inl(DE4X5_SISR) & SISR_NRA) {
2630 lp->media = AUI; /* Non selected port activity */
2634 next_tick = dc21041_autoconf(dev);
2636 lp->local_state = 1;
2637 de4x5_init_connection(dev);
2640 } else if (!lp->linkOK && (lp->autosense == AUTO)) {
2641 lp->media = TP_SUSPECT;
2647 next_tick = de4x5_suspect_state(dev, 1000, TP, test_tp, dc21041_autoconf);
2651 if (!lp->tx_enable) {
2652 if (lp->timeout < 0) {
2653 omr = inl(DE4X5_OMR); /* Set up half duplex for AUI */
2654 outl(omr & ~OMR_FDX, DE4X5_OMR);
2658 sts = test_media(dev,irqs, irq_mask, 0xef09, 0xf73d, 0x000e, 1000);
2660 next_tick = sts & ~TIMER_CB;
2662 if (!(inl(DE4X5_SISR) & SISR_SRA) && (lp->autosense == AUTO)) {
2664 next_tick = dc21041_autoconf(dev);
2666 lp->local_state = 1;
2667 de4x5_init_connection(dev);
2670 } else if (!lp->linkOK && (lp->autosense == AUTO)) {
2671 lp->media = AUI_SUSPECT;
2677 next_tick = de4x5_suspect_state(dev, 1000, AUI, ping_media, dc21041_autoconf);
2681 switch (lp->local_state) {
2683 if (lp->timeout < 0) {
2684 omr = inl(DE4X5_OMR); /* Set up half duplex for BNC */
2685 outl(omr & ~OMR_FDX, DE4X5_OMR);
2689 sts = test_media(dev,irqs, irq_mask, 0xef09, 0xf73d, 0x0006, 1000);
2691 next_tick = sts & ~TIMER_CB;
2693 lp->local_state++; /* Ensure media connected */
2694 next_tick = dc21041_autoconf(dev);
2699 if (!lp->tx_enable) {
2700 if ((sts = ping_media(dev, 3000)) < 0) {
2701 next_tick = sts & ~TIMER_CB;
2704 lp->local_state = 0;
2707 de4x5_init_connection(dev);
2710 } else if (!lp->linkOK && (lp->autosense == AUTO)) {
2711 lp->media = BNC_SUSPECT;
2719 next_tick = de4x5_suspect_state(dev, 1000, BNC, ping_media, dc21041_autoconf);
2723 omr = inl(DE4X5_OMR); /* Set up full duplex for the autonegotiate */
2724 outl(omr | OMR_FDX, DE4X5_OMR);
2725 reset_init_sia(dev, 0xef01, 0xffff, 0x0008);/* Initialise the SIA */
2726 if (lp->media != lp->c_media) {
2727 de4x5_dbg_media(dev);
2728 lp->c_media = lp->media;
2731 lp->tx_enable = false;
2739 ** Some autonegotiation chips are broken in that they do not return the
2740 ** acknowledge bit (anlpa & MII_ANLPA_ACK) in the link partner advertisement
2741 ** register, except at the first power up negotiation.
2744 dc21140m_autoconf(struct net_device *dev)
2746 struct de4x5_private *lp = netdev_priv(dev);
2747 int ana, anlpa, cap, cr, slnk, sr;
2748 int next_tick = DE4X5_AUTOSENSE_MS;
2749 u_long imr, omr, iobase = dev->base_addr;
2753 if (lp->timeout < 0) {
2755 lp->tx_enable = false;
2757 de4x5_save_skbs(dev); /* Save non transmitted skb's */
2759 if ((next_tick = de4x5_reset_phy(dev)) < 0) {
2760 next_tick &= ~TIMER_CB;
2763 if (srom_map_media(dev) < 0) {
2767 srom_exec(dev, lp->phy[lp->active].gep);
2768 if (lp->infoblock_media == ANS) {
2769 ana = lp->phy[lp->active].ana | MII_ANA_CSMA;
2770 mii_wr(ana, MII_ANA, lp->phy[lp->active].addr, DE4X5_MII);
2773 lp->tmp = MII_SR_ASSC; /* Fake out the MII speed set */
2775 if (lp->autosense == _100Mb) {
2777 } else if (lp->autosense == _10Mb) {
2779 } else if ((lp->autosense == AUTO) &&
2780 ((sr=is_anc_capable(dev)) & MII_SR_ANC)) {
2781 ana = (((sr >> 6) & MII_ANA_TAF) | MII_ANA_CSMA);
2782 ana &= (lp->fdx ? ~0 : ~MII_ANA_FDAM);
2783 mii_wr(ana, MII_ANA, lp->phy[lp->active].addr, DE4X5_MII);
2785 } else if (lp->autosense == AUTO) {
2786 lp->media = SPD_DET;
2787 } else if (is_spd_100(dev) && is_100_up(dev)) {
2793 lp->local_state = 0;
2794 next_tick = dc21140m_autoconf(dev);
2799 switch (lp->local_state) {
2801 if (lp->timeout < 0) {
2802 mii_wr(MII_CR_ASSE | MII_CR_RAN, MII_CR, lp->phy[lp->active].addr, DE4X5_MII);
2804 cr = test_mii_reg(dev, MII_CR, MII_CR_RAN, false, 500);
2806 next_tick = cr & ~TIMER_CB;
2809 lp->local_state = 0;
2810 lp->media = SPD_DET;
2814 next_tick = dc21140m_autoconf(dev);
2819 if ((sr=test_mii_reg(dev, MII_SR, MII_SR_ASSC, true, 2000)) < 0) {
2820 next_tick = sr & ~TIMER_CB;
2822 lp->media = SPD_DET;
2823 lp->local_state = 0;
2824 if (sr) { /* Success! */
2825 lp->tmp = MII_SR_ASSC;
2826 anlpa = mii_rd(MII_ANLPA, lp->phy[lp->active].addr, DE4X5_MII);
2827 ana = mii_rd(MII_ANA, lp->phy[lp->active].addr, DE4X5_MII);
2828 if (!(anlpa & MII_ANLPA_RF) &&
2829 (cap = anlpa & MII_ANLPA_TAF & ana)) {
2830 if (cap & MII_ANA_100M) {
2831 lp->fdx = (ana & anlpa & MII_ANA_FDAM & MII_ANA_100M) != 0;
2833 } else if (cap & MII_ANA_10M) {
2834 lp->fdx = (ana & anlpa & MII_ANA_FDAM & MII_ANA_10M) != 0;
2839 } /* Auto Negotiation failed to finish */
2840 next_tick = dc21140m_autoconf(dev);
2841 } /* Auto Negotiation failed to start */
2846 case SPD_DET: /* Choose 10Mb/s or 100Mb/s */
2847 if (lp->timeout < 0) {
2848 lp->tmp = (lp->phy[lp->active].id ? MII_SR_LKS :
2849 (~gep_rd(dev) & GEP_LNP));
2852 if ((slnk = test_for_100Mb(dev, 6500)) < 0) {
2853 next_tick = slnk & ~TIMER_CB;
2855 if (is_spd_100(dev) && is_100_up(dev)) {
2857 } else if ((!is_spd_100(dev) && (is_10_up(dev) & lp->tmp))) {
2862 next_tick = dc21140m_autoconf(dev);
2866 case _100Mb: /* Set 100Mb/s */
2868 if (!lp->tx_enable) {
2870 de4x5_init_connection(dev);
2872 if (!lp->linkOK && (lp->autosense == AUTO)) {
2873 if (!is_100_up(dev) || (!lp->useSROM && !is_spd_100(dev))) {
2876 next_tick = DE4X5_AUTOSENSE_MS;
2884 case _10Mb: /* Set 10Mb/s */
2886 if (!lp->tx_enable) {
2888 de4x5_init_connection(dev);
2890 if (!lp->linkOK && (lp->autosense == AUTO)) {
2891 if (!is_10_up(dev) || (!lp->useSROM && is_spd_100(dev))) {
2894 next_tick = DE4X5_AUTOSENSE_MS;
2901 if (lp->media != lp->c_media) {
2902 de4x5_dbg_media(dev);
2903 lp->c_media = lp->media;
2906 lp->tx_enable = false;
2914 ** This routine may be merged into dc21140m_autoconf() sometime as I'm
2915 ** changing how I figure out the media - but trying to keep it backwards
2916 ** compatible with the de500-xa and de500-aa.
2917 ** Whether it's BNC, AUI, SYM or MII is sorted out in the infoblock
2918 ** functions and set during de4x5_mac_port() and/or de4x5_reset_phy().
2919 ** This routine just has to figure out whether 10Mb/s or 100Mb/s is
2921 ** When autonegotiation is working, the ANS part searches the SROM for
2922 ** the highest common speed (TP) link that both can run and if that can
2923 ** be full duplex. That infoblock is executed and then the link speed set.
2925 ** Only _10Mb and _100Mb are tested here.
2928 dc2114x_autoconf(struct net_device *dev)
2930 struct de4x5_private *lp = netdev_priv(dev);
2931 u_long iobase = dev->base_addr;
2932 s32 cr, anlpa, ana, cap, irqs, irq_mask, imr, omr, slnk, sr, sts;
2933 int next_tick = DE4X5_AUTOSENSE_MS;
2935 switch (lp->media) {
2937 if (lp->timeout < 0) {
2939 lp->tx_enable = false;
2942 de4x5_save_skbs(dev); /* Save non transmitted skb's */
2943 if (lp->params.autosense & ~AUTO) {
2944 srom_map_media(dev); /* Fixed media requested */
2945 if (lp->media != lp->params.autosense) {
2953 if ((next_tick = de4x5_reset_phy(dev)) < 0) {
2954 next_tick &= ~TIMER_CB;
2956 if (lp->autosense == _100Mb) {
2958 } else if (lp->autosense == _10Mb) {
2960 } else if (lp->autosense == TP) {
2962 } else if (lp->autosense == BNC) {
2964 } else if (lp->autosense == AUI) {
2967 lp->media = SPD_DET;
2968 if ((lp->infoblock_media == ANS) &&
2969 ((sr=is_anc_capable(dev)) & MII_SR_ANC)) {
2970 ana = (((sr >> 6) & MII_ANA_TAF) | MII_ANA_CSMA);
2971 ana &= (lp->fdx ? ~0 : ~MII_ANA_FDAM);
2972 mii_wr(ana, MII_ANA, lp->phy[lp->active].addr, DE4X5_MII);
2976 lp->local_state = 0;
2977 next_tick = dc2114x_autoconf(dev);
2982 switch (lp->local_state) {
2984 if (lp->timeout < 0) {
2985 mii_wr(MII_CR_ASSE | MII_CR_RAN, MII_CR, lp->phy[lp->active].addr, DE4X5_MII);
2987 cr = test_mii_reg(dev, MII_CR, MII_CR_RAN, false, 500);
2989 next_tick = cr & ~TIMER_CB;
2992 lp->local_state = 0;
2993 lp->media = SPD_DET;
2997 next_tick = dc2114x_autoconf(dev);
3002 sr = test_mii_reg(dev, MII_SR, MII_SR_ASSC, true, 2000);
3004 next_tick = sr & ~TIMER_CB;
3006 lp->media = SPD_DET;
3007 lp->local_state = 0;
3008 if (sr) { /* Success! */
3009 lp->tmp = MII_SR_ASSC;
3010 anlpa = mii_rd(MII_ANLPA, lp->phy[lp->active].addr, DE4X5_MII);
3011 ana = mii_rd(MII_ANA, lp->phy[lp->active].addr, DE4X5_MII);
3012 if (!(anlpa & MII_ANLPA_RF) &&
3013 (cap = anlpa & MII_ANLPA_TAF & ana)) {
3014 if (cap & MII_ANA_100M) {
3015 lp->fdx = (ana & anlpa & MII_ANA_FDAM & MII_ANA_100M) != 0;
3017 } else if (cap & MII_ANA_10M) {
3018 lp->fdx = (ana & anlpa & MII_ANA_FDAM & MII_ANA_10M) != 0;
3022 } /* Auto Negotiation failed to finish */
3023 next_tick = dc2114x_autoconf(dev);
3024 } /* Auto Negotiation failed to start */
3030 if (!lp->tx_enable) {
3031 if (lp->timeout < 0) {
3032 omr = inl(DE4X5_OMR); /* Set up half duplex for AUI */
3033 outl(omr & ~OMR_FDX, DE4X5_OMR);
3037 sts = test_media(dev,irqs, irq_mask, 0, 0, 0, 1000);
3039 next_tick = sts & ~TIMER_CB;
3041 if (!(inl(DE4X5_SISR) & SISR_SRA) && (lp->autosense == AUTO)) {
3043 next_tick = dc2114x_autoconf(dev);
3045 lp->local_state = 1;
3046 de4x5_init_connection(dev);
3049 } else if (!lp->linkOK && (lp->autosense == AUTO)) {
3050 lp->media = AUI_SUSPECT;
3056 next_tick = de4x5_suspect_state(dev, 1000, AUI, ping_media, dc2114x_autoconf);
3060 switch (lp->local_state) {
3062 if (lp->timeout < 0) {
3063 omr = inl(DE4X5_OMR); /* Set up half duplex for BNC */
3064 outl(omr & ~OMR_FDX, DE4X5_OMR);
3068 sts = test_media(dev,irqs, irq_mask, 0, 0, 0, 1000);
3070 next_tick = sts & ~TIMER_CB;
3072 lp->local_state++; /* Ensure media connected */
3073 next_tick = dc2114x_autoconf(dev);
3078 if (!lp->tx_enable) {
3079 if ((sts = ping_media(dev, 3000)) < 0) {
3080 next_tick = sts & ~TIMER_CB;
3083 lp->local_state = 0;
3087 de4x5_init_connection(dev);
3090 } else if (!lp->linkOK && (lp->autosense == AUTO)) {
3091 lp->media = BNC_SUSPECT;
3099 next_tick = de4x5_suspect_state(dev, 1000, BNC, ping_media, dc2114x_autoconf);
3102 case SPD_DET: /* Choose 10Mb/s or 100Mb/s */
3103 if (srom_map_media(dev) < 0) {
3108 if (lp->media == _100Mb) {
3109 if ((slnk = test_for_100Mb(dev, 6500)) < 0) {
3110 lp->media = SPD_DET;
3111 return slnk & ~TIMER_CB;
3114 if (wait_for_link(dev) < 0) {
3115 lp->media = SPD_DET;
3116 return PDET_LINK_WAIT;
3119 if (lp->media == ANS) { /* Do MII parallel detection */
3120 if (is_spd_100(dev)) {
3125 next_tick = dc2114x_autoconf(dev);
3126 } else if (((lp->media == _100Mb) && is_100_up(dev)) ||
3127 (((lp->media == _10Mb) || (lp->media == TP) ||
3128 (lp->media == BNC) || (lp->media == AUI)) &&
3130 next_tick = dc2114x_autoconf(dev);
3139 if (!lp->tx_enable) {
3141 de4x5_init_connection(dev);
3143 if (!lp->linkOK && (lp->autosense == AUTO)) {
3144 if (!is_10_up(dev) || (!lp->useSROM && is_spd_100(dev))) {
3147 next_tick = DE4X5_AUTOSENSE_MS;
3155 if (!lp->tx_enable) {
3157 de4x5_init_connection(dev);
3159 if (!lp->linkOK && (lp->autosense == AUTO)) {
3160 if (!is_100_up(dev) || (!lp->useSROM && !is_spd_100(dev))) {
3163 next_tick = DE4X5_AUTOSENSE_MS;
3171 printk("Huh?: media:%02x\n", lp->media);
3180 srom_autoconf(struct net_device *dev)
3182 struct de4x5_private *lp = netdev_priv(dev);
3184 return lp->infoleaf_fn(dev);
3188 ** This mapping keeps the original media codes and FDX flag unchanged.
3189 ** While it isn't strictly necessary, it helps me for the moment...
3190 ** The early return avoids a media state / SROM media space clash.
3193 srom_map_media(struct net_device *dev)
3195 struct de4x5_private *lp = netdev_priv(dev);
3198 if (lp->infoblock_media == lp->media)
3201 switch(lp->infoblock_media) {
3203 if (!lp->params.fdx) return -1;
3206 if (lp->params.fdx && !lp->fdx) return -1;
3207 if ((lp->chipset == DC21140) || ((lp->chipset & ~0x00ff) == DC2114x)) {
3222 case SROM_100BASETF:
3223 if (!lp->params.fdx) return -1;
3226 if (lp->params.fdx && !lp->fdx) return -1;
3230 case SROM_100BASET4:
3234 case SROM_100BASEFF:
3235 if (!lp->params.fdx) return -1;
3238 if (lp->params.fdx && !lp->fdx) return -1;
3244 lp->fdx = lp->params.fdx;
3248 printk("%s: Bad media code [%d] detected in SROM!\n", dev->name,
3249 lp->infoblock_media);
3257 de4x5_init_connection(struct net_device *dev)
3259 struct de4x5_private *lp = netdev_priv(dev);
3260 u_long iobase = dev->base_addr;
3263 if (lp->media != lp->c_media) {
3264 de4x5_dbg_media(dev);
3265 lp->c_media = lp->media; /* Stop scrolling media messages */
3268 spin_lock_irqsave(&lp->lock, flags);
3269 de4x5_rst_desc_ring(dev);
3270 de4x5_setup_intr(dev);
3271 lp->tx_enable = true;
3272 spin_unlock_irqrestore(&lp->lock, flags);
3273 outl(POLL_DEMAND, DE4X5_TPD);
3275 netif_wake_queue(dev);
3279 ** General PHY reset function. Some MII devices don't reset correctly
3280 ** since their MII address pins can float at voltages that are dependent
3281 ** on the signal pin use. Do a double reset to ensure a reset.
3284 de4x5_reset_phy(struct net_device *dev)
3286 struct de4x5_private *lp = netdev_priv(dev);
3287 u_long iobase = dev->base_addr;
3290 if ((lp->useSROM) || (lp->phy[lp->active].id)) {
3291 if (lp->timeout < 0) {
3293 if (lp->phy[lp->active].rst) {
3294 srom_exec(dev, lp->phy[lp->active].rst);
3295 srom_exec(dev, lp->phy[lp->active].rst);
3296 } else if (lp->rst) { /* Type 5 infoblock reset */
3297 srom_exec(dev, lp->rst);
3298 srom_exec(dev, lp->rst);
3304 mii_wr(MII_CR_RST, MII_CR, lp->phy[lp->active].addr, DE4X5_MII);
3308 next_tick = test_mii_reg(dev, MII_CR, MII_CR_RST, false, 500);
3310 } else if (lp->chipset == DC21140) {
3318 test_media(struct net_device *dev, s32 irqs, s32 irq_mask, s32 csr13, s32 csr14, s32 csr15, s32 msec)
3320 struct de4x5_private *lp = netdev_priv(dev);
3321 u_long iobase = dev->base_addr;
3324 if (lp->timeout < 0) {
3325 lp->timeout = msec/100;
3326 if (!lp->useSROM) { /* Already done if by SROM, else dc2104[01] */
3327 reset_init_sia(dev, csr13, csr14, csr15);
3330 /* set up the interrupt mask */
3331 outl(irq_mask, DE4X5_IMR);
3333 /* clear all pending interrupts */
3334 sts = inl(DE4X5_STS);
3335 outl(sts, DE4X5_STS);
3337 /* clear csr12 NRA and SRA bits */
3338 if ((lp->chipset == DC21041) || lp->useSROM) {
3339 csr12 = inl(DE4X5_SISR);
3340 outl(csr12, DE4X5_SISR);
3344 sts = inl(DE4X5_STS) & ~TIMER_CB;
3346 if (!(sts & irqs) && --lp->timeout) {
3347 sts = 100 | TIMER_CB;
3356 test_tp(struct net_device *dev, s32 msec)
3358 struct de4x5_private *lp = netdev_priv(dev);
3359 u_long iobase = dev->base_addr;
3362 if (lp->timeout < 0) {
3363 lp->timeout = msec/100;
3366 sisr = (inl(DE4X5_SISR) & ~TIMER_CB) & (SISR_LKF | SISR_NCR);
3368 if (sisr && --lp->timeout) {
3369 sisr = 100 | TIMER_CB;
3378 ** Samples the 100Mb Link State Signal. The sample interval is important
3379 ** because too fast a rate can give erroneous results and confuse the
3380 ** speed sense algorithm.
3382 #define SAMPLE_INTERVAL 500 /* ms */
3383 #define SAMPLE_DELAY 2000 /* ms */
3385 test_for_100Mb(struct net_device *dev, int msec)
3387 struct de4x5_private *lp = netdev_priv(dev);
3388 int gep = 0, ret = ((lp->chipset & ~0x00ff)==DC2114x? -1 :GEP_SLNK);
3390 if (lp->timeout < 0) {
3391 if ((msec/SAMPLE_INTERVAL) <= 0) return 0;
3392 if (msec > SAMPLE_DELAY) {
3393 lp->timeout = (msec - SAMPLE_DELAY)/SAMPLE_INTERVAL;
3394 gep = SAMPLE_DELAY | TIMER_CB;
3397 lp->timeout = msec/SAMPLE_INTERVAL;
3401 if (lp->phy[lp->active].id || lp->useSROM) {
3402 gep = is_100_up(dev) | is_spd_100(dev);
3404 gep = (~gep_rd(dev) & (GEP_SLNK | GEP_LNP));
3406 if (!(gep & ret) && --lp->timeout) {
3407 gep = SAMPLE_INTERVAL | TIMER_CB;
3416 wait_for_link(struct net_device *dev)
3418 struct de4x5_private *lp = netdev_priv(dev);
3420 if (lp->timeout < 0) {
3424 if (lp->timeout--) {
3438 test_mii_reg(struct net_device *dev, int reg, int mask, bool pol, long msec)
3440 struct de4x5_private *lp = netdev_priv(dev);
3442 u_long iobase = dev->base_addr;
3444 if (lp->timeout < 0) {
3445 lp->timeout = msec/100;
3448 reg = mii_rd((u_char)reg, lp->phy[lp->active].addr, DE4X5_MII) & mask;
3449 test = (reg ^ (pol ? ~0 : 0)) & mask;
3451 if (test && --lp->timeout) {
3452 reg = 100 | TIMER_CB;
3461 is_spd_100(struct net_device *dev)
3463 struct de4x5_private *lp = netdev_priv(dev);
3464 u_long iobase = dev->base_addr;
3468 spd = mii_rd(lp->phy[lp->active].spd.reg, lp->phy[lp->active].addr, DE4X5_MII);
3469 spd = ~(spd ^ lp->phy[lp->active].spd.value);
3470 spd &= lp->phy[lp->active].spd.mask;
3471 } else if (!lp->useSROM) { /* de500-xa */
3472 spd = ((~gep_rd(dev)) & GEP_SLNK);
3474 if ((lp->ibn == 2) || !lp->asBitValid)
3475 return (lp->chipset == DC21143) ? (~inl(DE4X5_SISR)&SISR_LS100) : 0;
3477 spd = (lp->asBitValid & (lp->asPolarity ^ (gep_rd(dev) & lp->asBit))) |
3478 (lp->linkOK & ~lp->asBitValid);
3485 is_100_up(struct net_device *dev)
3487 struct de4x5_private *lp = netdev_priv(dev);
3488 u_long iobase = dev->base_addr;
3491 /* Double read for sticky bits & temporary drops */
3492 mii_rd(MII_SR, lp->phy[lp->active].addr, DE4X5_MII);
3493 return mii_rd(MII_SR, lp->phy[lp->active].addr, DE4X5_MII) & MII_SR_LKS;
3494 } else if (!lp->useSROM) { /* de500-xa */
3495 return (~gep_rd(dev)) & GEP_SLNK;
3497 if ((lp->ibn == 2) || !lp->asBitValid)
3498 return (lp->chipset == DC21143) ? (~inl(DE4X5_SISR)&SISR_LS100) : 0;
3500 return (lp->asBitValid&(lp->asPolarity^(gep_rd(dev)&lp->asBit))) |
3501 (lp->linkOK & ~lp->asBitValid);
3506 is_10_up(struct net_device *dev)
3508 struct de4x5_private *lp = netdev_priv(dev);
3509 u_long iobase = dev->base_addr;
3512 /* Double read for sticky bits & temporary drops */
3513 mii_rd(MII_SR, lp->phy[lp->active].addr, DE4X5_MII);
3514 return mii_rd(MII_SR, lp->phy[lp->active].addr, DE4X5_MII) & MII_SR_LKS;
3515 } else if (!lp->useSROM) { /* de500-xa */
3516 return (~gep_rd(dev)) & GEP_LNP;
3518 if ((lp->ibn == 2) || !lp->asBitValid)
3519 return ((lp->chipset & ~0x00ff) == DC2114x) ?
3520 (~inl(DE4X5_SISR)&SISR_LS10):
3523 return (lp->asBitValid&(lp->asPolarity^(gep_rd(dev)&lp->asBit))) |
3524 (lp->linkOK & ~lp->asBitValid);
3529 is_anc_capable(struct net_device *dev)
3531 struct de4x5_private *lp = netdev_priv(dev);
3532 u_long iobase = dev->base_addr;
3534 if (lp->phy[lp->active].id && (!lp->useSROM || lp->useMII)) {
3535 return mii_rd(MII_SR, lp->phy[lp->active].addr, DE4X5_MII);
3536 } else if ((lp->chipset & ~0x00ff) == DC2114x) {
3537 return (inl(DE4X5_SISR) & SISR_LPN) >> 12;
3544 ** Send a packet onto the media and watch for send errors that indicate the
3545 ** media is bad or unconnected.
3548 ping_media(struct net_device *dev, int msec)
3550 struct de4x5_private *lp = netdev_priv(dev);
3551 u_long iobase = dev->base_addr;
3554 if (lp->timeout < 0) {
3555 lp->timeout = msec/100;
3557 lp->tmp = lp->tx_new; /* Remember the ring position */
3558 load_packet(dev, lp->frame, TD_LS | TD_FS | sizeof(lp->frame), (struct sk_buff *)1);
3559 lp->tx_new = (lp->tx_new + 1) % lp->txRingSize;
3560 outl(POLL_DEMAND, DE4X5_TPD);
3563 sisr = inl(DE4X5_SISR);
3565 if ((!(sisr & SISR_NCR)) &&
3566 ((s32)le32_to_cpu(lp->tx_ring[lp->tmp].status) < 0) &&
3568 sisr = 100 | TIMER_CB;
3570 if ((!(sisr & SISR_NCR)) &&
3571 !(le32_to_cpu(lp->tx_ring[lp->tmp].status) & (T_OWN | TD_ES)) &&
3584 ** This function does 2 things: on Intels it kmalloc's another buffer to
3585 ** replace the one about to be passed up. On Alpha's it kmallocs a buffer
3586 ** into which the packet is copied.
3588 static struct sk_buff *
3589 de4x5_alloc_rx_buff(struct net_device *dev, int index, int len)
3591 struct de4x5_private *lp = netdev_priv(dev);
3594 #if !defined(__alpha__) && !defined(__powerpc__) && !defined(CONFIG_SPARC) && !defined(DE4X5_DO_MEMCPY)
3595 struct sk_buff *ret;
3598 p = netdev_alloc_skb(dev, IEEE802_3_SZ + DE4X5_ALIGN + 2);
3599 if (!p) return NULL;
3601 tmp = virt_to_bus(p->data);
3602 i = ((tmp + DE4X5_ALIGN) & ~DE4X5_ALIGN) - tmp;
3604 lp->rx_ring[index].buf = cpu_to_le32(tmp + i);
3606 ret = lp->rx_skb[index];
3607 lp->rx_skb[index] = p;
3609 if ((u_long) ret > 1) {
3616 if (lp->state != OPEN) return (struct sk_buff *)1; /* Fake out the open */
3618 p = netdev_alloc_skb(dev, len + 2);
3619 if (!p) return NULL;
3621 skb_reserve(p, 2); /* Align */
3622 if (index < lp->rx_old) { /* Wrapped buffer */
3623 short tlen = (lp->rxRingSize - lp->rx_old) * RX_BUFF_SZ;
3624 memcpy(skb_put(p,tlen),lp->rx_bufs + lp->rx_old * RX_BUFF_SZ,tlen);
3625 memcpy(skb_put(p,len-tlen),lp->rx_bufs,len-tlen);
3626 } else { /* Linear buffer */
3627 memcpy(skb_put(p,len),lp->rx_bufs + lp->rx_old * RX_BUFF_SZ,len);
3635 de4x5_free_rx_buffs(struct net_device *dev)
3637 struct de4x5_private *lp = netdev_priv(dev);
3640 for (i=0; i<lp->rxRingSize; i++) {
3641 if ((u_long) lp->rx_skb[i] > 1) {
3642 dev_kfree_skb(lp->rx_skb[i]);
3644 lp->rx_ring[i].status = 0;
3645 lp->rx_skb[i] = (struct sk_buff *)1; /* Dummy entry */
3650 de4x5_free_tx_buffs(struct net_device *dev)
3652 struct de4x5_private *lp = netdev_priv(dev);
3655 for (i=0; i<lp->txRingSize; i++) {
3657 de4x5_free_tx_buff(lp, i);
3658 lp->tx_ring[i].status = 0;
3661 /* Unload the locally queued packets */
3662 __skb_queue_purge(&lp->cache.queue);
3666 ** When a user pulls a connection, the DECchip can end up in a
3667 ** 'running - waiting for end of transmission' state. This means that we
3668 ** have to perform a chip soft reset to ensure that we can synchronize
3669 ** the hardware and software and make any media probes using a loopback
3670 ** packet meaningful.
3673 de4x5_save_skbs(struct net_device *dev)
3675 struct de4x5_private *lp = netdev_priv(dev);
3676 u_long iobase = dev->base_addr;
3679 if (!lp->cache.save_cnt) {
3681 de4x5_tx(dev); /* Flush any sent skb's */
3682 de4x5_free_tx_buffs(dev);
3683 de4x5_cache_state(dev, DE4X5_SAVE_STATE);
3684 de4x5_sw_reset(dev);
3685 de4x5_cache_state(dev, DE4X5_RESTORE_STATE);
3686 lp->cache.save_cnt++;
3692 de4x5_rst_desc_ring(struct net_device *dev)
3694 struct de4x5_private *lp = netdev_priv(dev);
3695 u_long iobase = dev->base_addr;
3699 if (lp->cache.save_cnt) {
3701 outl(lp->dma_rings, DE4X5_RRBA);
3702 outl(lp->dma_rings + NUM_RX_DESC * sizeof(struct de4x5_desc),
3705 lp->rx_new = lp->rx_old = 0;
3706 lp->tx_new = lp->tx_old = 0;
3708 for (i = 0; i < lp->rxRingSize; i++) {
3709 lp->rx_ring[i].status = cpu_to_le32(R_OWN);
3712 for (i = 0; i < lp->txRingSize; i++) {
3713 lp->tx_ring[i].status = cpu_to_le32(0);
3717 lp->cache.save_cnt--;
3723 de4x5_cache_state(struct net_device *dev, int flag)
3725 struct de4x5_private *lp = netdev_priv(dev);
3726 u_long iobase = dev->base_addr;
3729 case DE4X5_SAVE_STATE:
3730 lp->cache.csr0 = inl(DE4X5_BMR);
3731 lp->cache.csr6 = (inl(DE4X5_OMR) & ~(OMR_ST | OMR_SR));
3732 lp->cache.csr7 = inl(DE4X5_IMR);
3735 case DE4X5_RESTORE_STATE:
3736 outl(lp->cache.csr0, DE4X5_BMR);
3737 outl(lp->cache.csr6, DE4X5_OMR);
3738 outl(lp->cache.csr7, DE4X5_IMR);
3739 if (lp->chipset == DC21140) {
3740 gep_wr(lp->cache.gepc, dev);
3741 gep_wr(lp->cache.gep, dev);
3743 reset_init_sia(dev, lp->cache.csr13, lp->cache.csr14,
3751 de4x5_put_cache(struct net_device *dev, struct sk_buff *skb)
3753 struct de4x5_private *lp = netdev_priv(dev);
3755 __skb_queue_tail(&lp->cache.queue, skb);
3759 de4x5_putb_cache(struct net_device *dev, struct sk_buff *skb)
3761 struct de4x5_private *lp = netdev_priv(dev);
3763 __skb_queue_head(&lp->cache.queue, skb);
3766 static struct sk_buff *
3767 de4x5_get_cache(struct net_device *dev)
3769 struct de4x5_private *lp = netdev_priv(dev);
3771 return __skb_dequeue(&lp->cache.queue);
3775 ** Check the Auto Negotiation State. Return OK when a link pass interrupt
3776 ** is received and the auto-negotiation status is NWAY OK.
3779 test_ans(struct net_device *dev, s32 irqs, s32 irq_mask, s32 msec)
3781 struct de4x5_private *lp = netdev_priv(dev);
3782 u_long iobase = dev->base_addr;
3785 if (lp->timeout < 0) {
3786 lp->timeout = msec/100;
3787 outl(irq_mask, DE4X5_IMR);
3789 /* clear all pending interrupts */
3790 sts = inl(DE4X5_STS);
3791 outl(sts, DE4X5_STS);
3794 ans = inl(DE4X5_SISR) & SISR_ANS;
3795 sts = inl(DE4X5_STS) & ~TIMER_CB;
3797 if (!(sts & irqs) && (ans ^ ANS_NWOK) && --lp->timeout) {
3798 sts = 100 | TIMER_CB;
3807 de4x5_setup_intr(struct net_device *dev)
3809 struct de4x5_private *lp = netdev_priv(dev);
3810 u_long iobase = dev->base_addr;
3813 if (inl(DE4X5_OMR) & OMR_SR) { /* Only unmask if TX/RX is enabled */
3816 sts = inl(DE4X5_STS); /* Reset any pending (stale) interrupts */
3817 outl(sts, DE4X5_STS);
3826 reset_init_sia(struct net_device *dev, s32 csr13, s32 csr14, s32 csr15)
3828 struct de4x5_private *lp = netdev_priv(dev);
3829 u_long iobase = dev->base_addr;
3834 srom_exec(dev, lp->phy[lp->active].rst);
3835 srom_exec(dev, lp->phy[lp->active].gep);
3836 outl(1, DE4X5_SICR);
3839 csr15 = lp->cache.csr15;
3840 csr14 = lp->cache.csr14;
3841 csr13 = lp->cache.csr13;
3842 outl(csr15 | lp->cache.gepc, DE4X5_SIGR);
3843 outl(csr15 | lp->cache.gep, DE4X5_SIGR);
3846 outl(csr15, DE4X5_SIGR);
3848 outl(csr14, DE4X5_STRR);
3849 outl(csr13, DE4X5_SICR);
3855 ** Create a loopback ethernet packet
3858 create_packet(struct net_device *dev, char *frame, int len)
3863 for (i=0; i<ETH_ALEN; i++) { /* Use this source address */
3864 *buf++ = dev->dev_addr[i];
3866 for (i=0; i<ETH_ALEN; i++) { /* Use this destination address */
3867 *buf++ = dev->dev_addr[i];
3870 *buf++ = 0; /* Packet length (2 bytes) */
3875 ** Look for a particular board name in the EISA configuration space
3878 EISA_signature(char *name, struct device *device)
3880 int i, status = 0, siglen = ARRAY_SIZE(de4x5_signatures);
3881 struct eisa_device *edev;
3884 edev = to_eisa_device (device);
3885 i = edev->id.driver_data;
3887 if (i >= 0 && i < siglen) {
3888 strcpy (name, de4x5_signatures[i]);
3892 return status; /* return the device name string */
3896 ** Look for a particular board name in the PCI configuration space
3899 PCI_signature(char *name, struct de4x5_private *lp)
3901 int i, status = 0, siglen = ARRAY_SIZE(de4x5_signatures);
3903 if (lp->chipset == DC21040) {
3904 strcpy(name, "DE434/5");
3906 } else { /* Search for a DEC name in the SROM */
3907 int tmp = *((char *)&lp->srom + 19) * 3;
3908 strncpy(name, (char *)&lp->srom + 26 + tmp, 8);
3911 for (i=0; i<siglen; i++) {
3912 if (strstr(name,de4x5_signatures[i])!=NULL) break;
3917 } else { /* Use chip name to avoid confusion */
3918 strcpy(name, (((lp->chipset == DC21040) ? "DC21040" :
3919 ((lp->chipset == DC21041) ? "DC21041" :
3920 ((lp->chipset == DC21140) ? "DC21140" :
3921 ((lp->chipset == DC21142) ? "DC21142" :
3922 ((lp->chipset == DC21143) ? "DC21143" : "UNKNOWN"
3925 if (lp->chipset != DC21041) {
3926 lp->useSROM = true; /* card is not recognisably DEC */
3928 } else if ((lp->chipset & ~0x00ff) == DC2114x) {
3936 ** Set up the Ethernet PROM counter to the start of the Ethernet address on
3937 ** the DC21040, else read the SROM for the other chips.
3938 ** The SROM may not be present in a multi-MAC card, so first read the
3939 ** MAC address and check for a bad address. If there is a bad one then exit
3940 ** immediately with the prior srom contents intact (the h/w address will
3941 ** be fixed up later).
3944 DevicePresent(struct net_device *dev, u_long aprom_addr)
3947 struct de4x5_private *lp = netdev_priv(dev);
3949 if (lp->chipset == DC21040) {
3950 if (lp->bus == EISA) {
3951 enet_addr_rst(aprom_addr); /* Reset Ethernet Address ROM Pointer */
3953 outl(0, aprom_addr); /* Reset Ethernet Address ROM Pointer */
3955 } else { /* Read new srom */
3957 __le16 *p = (__le16 *)((char *)&lp->srom + SROM_HWADD);
3958 for (i=0; i<(ETH_ALEN>>1); i++) {
3959 tmp = srom_rd(aprom_addr, (SROM_HWADD>>1) + i);
3960 j += tmp; /* for check for 0:0:0:0:0:0 or ff:ff:ff:ff:ff:ff */
3961 *p = cpu_to_le16(tmp);
3963 if (j == 0 || j == 3 * 0xffff) {
3964 /* could get 0 only from all-0 and 3 * 0xffff only from all-1 */
3968 p = (__le16 *)&lp->srom;
3969 for (i=0; i<(sizeof(struct de4x5_srom)>>1); i++) {
3970 tmp = srom_rd(aprom_addr, i);
3971 *p++ = cpu_to_le16(tmp);
3973 de4x5_dbg_srom(&lp->srom);
3978 ** Since the write on the Enet PROM register doesn't seem to reset the PROM
3979 ** pointer correctly (at least on my DE425 EISA card), this routine should do
3980 ** it...from depca.c.
3983 enet_addr_rst(u_long aprom_addr)
3990 char Sig[sizeof(u32) << 1];
3996 dev.llsig.a = ETH_PROM_SIG;
3997 dev.llsig.b = ETH_PROM_SIG;
3998 sigLength = sizeof(u32) << 1;
4000 for (i=0,j=0;j<sigLength && i<PROBE_LENGTH+sigLength-1;i++) {
4001 data = inb(aprom_addr);
4002 if (dev.Sig[j] == data) { /* track signature */
4004 } else { /* lost signature; begin search again */
4005 if (data == dev.Sig[0]) { /* rare case.... */
4015 ** For the bad status case and no SROM, then add one to the previous
4016 ** address. However, need to add one backwards in case we have 0xff
4017 ** as one or more of the bytes. Only the last 3 bytes should be checked
4018 ** as the first three are invariant - assigned to an organisation.
4021 get_hw_addr(struct net_device *dev)
4023 u_long iobase = dev->base_addr;
4024 int broken, i, k, tmp, status = 0;
4026 struct de4x5_private *lp = netdev_priv(dev);
4028 broken = de4x5_bad_srom(lp);
4030 for (i=0,k=0,j=0;j<3;j++) {
4032 if (k > 0xffff) k-=0xffff;
4034 if (lp->bus == PCI) {
4035 if (lp->chipset == DC21040) {
4036 while ((tmp = inl(DE4X5_APROM)) < 0);
4038 dev->dev_addr[i++] = (u_char) tmp;
4039 while ((tmp = inl(DE4X5_APROM)) < 0);
4040 k += (u_short) (tmp << 8);
4041 dev->dev_addr[i++] = (u_char) tmp;
4042 } else if (!broken) {
4043 dev->dev_addr[i] = (u_char) lp->srom.ieee_addr[i]; i++;
4044 dev->dev_addr[i] = (u_char) lp->srom.ieee_addr[i]; i++;
4045 } else if ((broken == SMC) || (broken == ACCTON)) {
4046 dev->dev_addr[i] = *((u_char *)&lp->srom + i); i++;
4047 dev->dev_addr[i] = *((u_char *)&lp->srom + i); i++;
4050 k += (u_char) (tmp = inb(EISA_APROM));
4051 dev->dev_addr[i++] = (u_char) tmp;
4052 k += (u_short) ((tmp = inb(EISA_APROM)) << 8);
4053 dev->dev_addr[i++] = (u_char) tmp;
4056 if (k > 0xffff) k-=0xffff;
4058 if (k == 0xffff) k=0;
4060 if (lp->bus == PCI) {
4061 if (lp->chipset == DC21040) {
4062 while ((tmp = inl(DE4X5_APROM)) < 0);
4063 chksum = (u_char) tmp;
4064 while ((tmp = inl(DE4X5_APROM)) < 0);
4065 chksum |= (u_short) (tmp << 8);
4066 if ((k != chksum) && (dec_only)) status = -1;
4069 chksum = (u_char) inb(EISA_APROM);
4070 chksum |= (u_short) (inb(EISA_APROM) << 8);
4071 if ((k != chksum) && (dec_only)) status = -1;
4074 /* If possible, try to fix a broken card - SMC only so far */
4075 srom_repair(dev, broken);
4077 #ifdef CONFIG_PPC_PMAC
4079 ** If the address starts with 00 a0, we have to bit-reverse
4080 ** each byte of the address.
4082 if ( machine_is(powermac) &&
4083 (dev->dev_addr[0] == 0) &&
4084 (dev->dev_addr[1] == 0xa0) )
4086 for (i = 0; i < ETH_ALEN; ++i)
4088 int x = dev->dev_addr[i];
4089 x = ((x & 0xf) << 4) + ((x & 0xf0) >> 4);
4090 x = ((x & 0x33) << 2) + ((x & 0xcc) >> 2);
4091 dev->dev_addr[i] = ((x & 0x55) << 1) + ((x & 0xaa) >> 1);
4094 #endif /* CONFIG_PPC_PMAC */
4096 /* Test for a bad enet address */
4097 status = test_bad_enet(dev, status);
4103 ** Test for enet addresses in the first 32 bytes.
4106 de4x5_bad_srom(struct de4x5_private *lp)
4110 for (i = 0; i < ARRAY_SIZE(enet_det); i++) {
4111 if (!memcmp(&lp->srom, &enet_det[i], 3) &&
4112 !memcmp((char *)&lp->srom+0x10, &enet_det[i], 3)) {
4115 } else if (i == 1) {
4126 srom_repair(struct net_device *dev, int card)
4128 struct de4x5_private *lp = netdev_priv(dev);
4132 memset((char *)&lp->srom, 0, sizeof(struct de4x5_srom));
4133 memcpy(lp->srom.ieee_addr, (char *)dev->dev_addr, ETH_ALEN);
4134 memcpy(lp->srom.info, (char *)&srom_repair_info[SMC-1], 100);
4141 ** Assume that the irq's do not follow the PCI spec - this is seems
4142 ** to be true so far (2 for 2).
4145 test_bad_enet(struct net_device *dev, int status)
4147 struct de4x5_private *lp = netdev_priv(dev);
4150 for (tmp=0,i=0; i<ETH_ALEN; i++) tmp += (u_char)dev->dev_addr[i];
4151 if ((tmp == 0) || (tmp == 0x5fa)) {
4152 if ((lp->chipset == last.chipset) &&
4153 (lp->bus_num == last.bus) && (lp->bus_num > 0)) {
4154 for (i=0; i<ETH_ALEN; i++) dev->dev_addr[i] = last.addr[i];
4155 for (i=ETH_ALEN-1; i>2; --i) {
4156 dev->dev_addr[i] += 1;
4157 if (dev->dev_addr[i] != 0) break;
4159 for (i=0; i<ETH_ALEN; i++) last.addr[i] = dev->dev_addr[i];
4160 if (!an_exception(lp)) {
4161 dev->irq = last.irq;
4166 } else if (!status) {
4167 last.chipset = lp->chipset;
4168 last.bus = lp->bus_num;
4169 last.irq = dev->irq;
4170 for (i=0; i<ETH_ALEN; i++) last.addr[i] = dev->dev_addr[i];
4177 ** List of board exceptions with correctly wired IRQs
4180 an_exception(struct de4x5_private *lp)
4182 if ((*(u_short *)lp->srom.sub_vendor_id == 0x00c0) &&
4183 (*(u_short *)lp->srom.sub_system_id == 0x95e0)) {
4194 srom_rd(u_long addr, u_char offset)
4196 sendto_srom(SROM_RD | SROM_SR, addr);
4198 srom_latch(SROM_RD | SROM_SR | DT_CS, addr);
4199 srom_command(SROM_RD | SROM_SR | DT_IN | DT_CS, addr);
4200 srom_address(SROM_RD | SROM_SR | DT_CS, addr, offset);
4202 return srom_data(SROM_RD | SROM_SR | DT_CS, addr);
4206 srom_latch(u_int command, u_long addr)
4208 sendto_srom(command, addr);
4209 sendto_srom(command | DT_CLK, addr);
4210 sendto_srom(command, addr);
4214 srom_command(u_int command, u_long addr)
4216 srom_latch(command, addr);
4217 srom_latch(command, addr);
4218 srom_latch((command & 0x0000ff00) | DT_CS, addr);
4222 srom_address(u_int command, u_long addr, u_char offset)
4227 for (i=0; i<6; i++, a <<= 1) {
4228 srom_latch(command | ((a & 0x80) ? DT_IN : 0), addr);
4232 i = (getfrom_srom(addr) >> 3) & 0x01;
4236 srom_data(u_int command, u_long addr)
4242 for (i=0; i<16; i++) {
4243 sendto_srom(command | DT_CLK, addr);
4244 tmp = getfrom_srom(addr);
4245 sendto_srom(command, addr);
4247 word = (word << 1) | ((tmp >> 3) & 0x01);
4250 sendto_srom(command & 0x0000ff00, addr);
4257 srom_busy(u_int command, u_long addr)
4259 sendto_srom((command & 0x0000ff00) | DT_CS, addr);
4261 while (!((getfrom_srom(addr) >> 3) & 0x01)) {
4265 sendto_srom(command & 0x0000ff00, addr);
4270 sendto_srom(u_int command, u_long addr)
4272 outl(command, addr);
4277 getfrom_srom(u_long addr)
4288 srom_infoleaf_info(struct net_device *dev)
4290 struct de4x5_private *lp = netdev_priv(dev);
4294 /* Find the infoleaf decoder function that matches this chipset */
4295 for (i=0; i<INFOLEAF_SIZE; i++) {
4296 if (lp->chipset == infoleaf_array[i].chipset) break;
4298 if (i == INFOLEAF_SIZE) {
4299 lp->useSROM = false;
4300 printk("%s: Cannot find correct chipset for SROM decoding!\n",
4305 lp->infoleaf_fn = infoleaf_array[i].fn;
4307 /* Find the information offset that this function should use */
4308 count = *((u_char *)&lp->srom + 19);
4309 p = (u_char *)&lp->srom + 26;
4312 for (i=count; i; --i, p+=3) {
4313 if (lp->device == *p) break;
4316 lp->useSROM = false;
4317 printk("%s: Cannot find correct PCI device [%d] for SROM decoding!\n",
4318 dev->name, lp->device);
4323 lp->infoleaf_offset = get_unaligned_le16(p + 1);
4329 ** This routine loads any type 1 or 3 MII info into the mii device
4330 ** struct and executes any type 5 code to reset PHY devices for this
4332 ** The info for the MII devices will be valid since the index used
4333 ** will follow the discovery process from MII address 1-31 then 0.
4336 srom_init(struct net_device *dev)
4338 struct de4x5_private *lp = netdev_priv(dev);
4339 u_char *p = (u_char *)&lp->srom + lp->infoleaf_offset;
4343 if (lp->chipset == DC21140) {
4344 lp->cache.gepc = (*p++ | GEP_CTRL);
4345 gep_wr(lp->cache.gepc, dev);
4351 /* Jump the infoblocks to find types */
4352 for (;count; --count) {
4355 } else if (*(p+1) == 5) {
4356 type5_infoblock(dev, 1, p);
4357 p += ((*p & BLOCK_LEN) + 1);
4358 } else if (*(p+1) == 4) {
4359 p += ((*p & BLOCK_LEN) + 1);
4360 } else if (*(p+1) == 3) {
4361 type3_infoblock(dev, 1, p);
4362 p += ((*p & BLOCK_LEN) + 1);
4363 } else if (*(p+1) == 2) {
4364 p += ((*p & BLOCK_LEN) + 1);
4365 } else if (*(p+1) == 1) {
4366 type1_infoblock(dev, 1, p);
4367 p += ((*p & BLOCK_LEN) + 1);
4369 p += ((*p & BLOCK_LEN) + 1);
4375 ** A generic routine that writes GEP control, data and reset information
4376 ** to the GEP register (21140) or csr15 GEP portion (2114[23]).
4379 srom_exec(struct net_device *dev, u_char *p)
4381 struct de4x5_private *lp = netdev_priv(dev);
4382 u_long iobase = dev->base_addr;
4383 u_char count = (p ? *p++ : 0);
4384 u_short *w = (u_short *)p;
4386 if (((lp->ibn != 1) && (lp->ibn != 3) && (lp->ibn != 5)) || !count) return;
4388 if (lp->chipset != DC21140) RESET_SIA;
4391 gep_wr(((lp->chipset==DC21140) && (lp->ibn!=5) ?
4392 *p++ : get_unaligned_le16(w++)), dev);
4393 mdelay(2); /* 2ms per action */
4396 if (lp->chipset != DC21140) {
4397 outl(lp->cache.csr14, DE4X5_STRR);
4398 outl(lp->cache.csr13, DE4X5_SICR);
4403 ** Basically this function is a NOP since it will never be called,
4404 ** unless I implement the DC21041 SROM functions. There's no need
4405 ** since the existing code will be satisfactory for all boards.
4408 dc21041_infoleaf(struct net_device *dev)
4410 return DE4X5_AUTOSENSE_MS;
4414 dc21140_infoleaf(struct net_device *dev)
4416 struct de4x5_private *lp = netdev_priv(dev);
4418 u_char *p = (u_char *)&lp->srom + lp->infoleaf_offset;
4419 int next_tick = DE4X5_AUTOSENSE_MS;
4421 /* Read the connection type */
4425 lp->cache.gepc = (*p++ | GEP_CTRL);
4430 /* Recursively figure out the info blocks */
4432 next_tick = dc_infoblock[COMPACT](dev, count, p);
4434 next_tick = dc_infoblock[*(p+1)](dev, count, p);
4437 if (lp->tcount == count) {
4439 if (lp->media != lp->c_media) {
4440 de4x5_dbg_media(dev);
4441 lp->c_media = lp->media;
4445 lp->tx_enable = false;
4448 return next_tick & ~TIMER_CB;
4452 dc21142_infoleaf(struct net_device *dev)
4454 struct de4x5_private *lp = netdev_priv(dev);
4456 u_char *p = (u_char *)&lp->srom + lp->infoleaf_offset;
4457 int next_tick = DE4X5_AUTOSENSE_MS;
4459 /* Read the connection type */
4465 /* Recursively figure out the info blocks */
4467 next_tick = dc_infoblock[COMPACT](dev, count, p);
4469 next_tick = dc_infoblock[*(p+1)](dev, count, p);
4472 if (lp->tcount == count) {
4474 if (lp->media != lp->c_media) {
4475 de4x5_dbg_media(dev);
4476 lp->c_media = lp->media;
4480 lp->tx_enable = false;
4483 return next_tick & ~TIMER_CB;
4487 dc21143_infoleaf(struct net_device *dev)
4489 struct de4x5_private *lp = netdev_priv(dev);
4491 u_char *p = (u_char *)&lp->srom + lp->infoleaf_offset;
4492 int next_tick = DE4X5_AUTOSENSE_MS;
4494 /* Read the connection type */
4500 /* Recursively figure out the info blocks */
4502 next_tick = dc_infoblock[COMPACT](dev, count, p);
4504 next_tick = dc_infoblock[*(p+1)](dev, count, p);
4506 if (lp->tcount == count) {
4508 if (lp->media != lp->c_media) {
4509 de4x5_dbg_media(dev);
4510 lp->c_media = lp->media;
4514 lp->tx_enable = false;
4517 return next_tick & ~TIMER_CB;
4521 ** The compact infoblock is only designed for DC21140[A] chips, so
4522 ** we'll reuse the dc21140m_autoconf function. Non MII media only.
4525 compact_infoblock(struct net_device *dev, u_char count, u_char *p)
4527 struct de4x5_private *lp = netdev_priv(dev);
4530 /* Recursively figure out the info blocks */
4531 if (--count > lp->tcount) {
4532 if (*(p+COMPACT_LEN) < 128) {
4533 return dc_infoblock[COMPACT](dev, count, p+COMPACT_LEN);
4535 return dc_infoblock[*(p+COMPACT_LEN+1)](dev, count, p+COMPACT_LEN);
4539 if ((lp->media == INIT) && (lp->timeout < 0)) {
4542 gep_wr(lp->cache.gepc, dev);
4543 lp->infoblock_media = (*p++) & COMPACT_MC;
4544 lp->cache.gep = *p++;
4548 lp->asBitValid = (flags & 0x80) ? 0 : -1;
4549 lp->defMedium = (flags & 0x40) ? -1 : 0;
4550 lp->asBit = 1 << ((csr6 >> 1) & 0x07);
4551 lp->asPolarity = ((csr6 & 0x80) ? -1 : 0) & lp->asBit;
4552 lp->infoblock_csr6 = OMR_DEF | ((csr6 & 0x71) << 18);
4555 de4x5_switch_mac_port(dev);
4558 return dc21140m_autoconf(dev);
4562 ** This block describes non MII media for the DC21140[A] only.
4565 type0_infoblock(struct net_device *dev, u_char count, u_char *p)
4567 struct de4x5_private *lp = netdev_priv(dev);
4568 u_char flags, csr6, len = (*p & BLOCK_LEN)+1;
4570 /* Recursively figure out the info blocks */
4571 if (--count > lp->tcount) {
4572 if (*(p+len) < 128) {
4573 return dc_infoblock[COMPACT](dev, count, p+len);
4575 return dc_infoblock[*(p+len+1)](dev, count, p+len);
4579 if ((lp->media == INIT) && (lp->timeout < 0)) {
4582 gep_wr(lp->cache.gepc, dev);
4584 lp->infoblock_media = (*p++) & BLOCK0_MC;
4585 lp->cache.gep = *p++;
4589 lp->asBitValid = (flags & 0x80) ? 0 : -1;
4590 lp->defMedium = (flags & 0x40) ? -1 : 0;
4591 lp->asBit = 1 << ((csr6 >> 1) & 0x07);
4592 lp->asPolarity = ((csr6 & 0x80) ? -1 : 0) & lp->asBit;
4593 lp->infoblock_csr6 = OMR_DEF | ((csr6 & 0x71) << 18);
4596 de4x5_switch_mac_port(dev);
4599 return dc21140m_autoconf(dev);
4602 /* These functions are under construction! */
4605 type1_infoblock(struct net_device *dev, u_char count, u_char *p)
4607 struct de4x5_private *lp = netdev_priv(dev);
4608 u_char len = (*p & BLOCK_LEN)+1;
4610 /* Recursively figure out the info blocks */
4611 if (--count > lp->tcount) {
4612 if (*(p+len) < 128) {
4613 return dc_infoblock[COMPACT](dev, count, p+len);
4615 return dc_infoblock[*(p+len+1)](dev, count, p+len);
4620 if (lp->state == INITIALISED) {
4623 lp->phy[lp->active].gep = (*p ? p : NULL); p += (*p + 1);
4624 lp->phy[lp->active].rst = (*p ? p : NULL); p += (*p + 1);
4625 lp->phy[lp->active].mc = get_unaligned_le16(p); p += 2;
4626 lp->phy[lp->active].ana = get_unaligned_le16(p); p += 2;
4627 lp->phy[lp->active].fdx = get_unaligned_le16(p); p += 2;
4628 lp->phy[lp->active].ttm = get_unaligned_le16(p);
4630 } else if ((lp->media == INIT) && (lp->timeout < 0)) {
4633 lp->infoblock_csr6 = OMR_MII_100;
4635 lp->infoblock_media = ANS;
4637 de4x5_switch_mac_port(dev);
4640 return dc21140m_autoconf(dev);
4644 type2_infoblock(struct net_device *dev, u_char count, u_char *p)
4646 struct de4x5_private *lp = netdev_priv(dev);
4647 u_char len = (*p & BLOCK_LEN)+1;
4649 /* Recursively figure out the info blocks */
4650 if (--count > lp->tcount) {
4651 if (*(p+len) < 128) {
4652 return dc_infoblock[COMPACT](dev, count, p+len);
4654 return dc_infoblock[*(p+len+1)](dev, count, p+len);
4658 if ((lp->media == INIT) && (lp->timeout < 0)) {
4662 lp->infoblock_media = (*p) & MEDIA_CODE;
4664 if ((*p++) & EXT_FIELD) {
4665 lp->cache.csr13 = get_unaligned_le16(p); p += 2;
4666 lp->cache.csr14 = get_unaligned_le16(p); p += 2;
4667 lp->cache.csr15 = get_unaligned_le16(p); p += 2;
4669 lp->cache.csr13 = CSR13;
4670 lp->cache.csr14 = CSR14;
4671 lp->cache.csr15 = CSR15;
4673 lp->cache.gepc = ((s32)(get_unaligned_le16(p)) << 16); p += 2;
4674 lp->cache.gep = ((s32)(get_unaligned_le16(p)) << 16);
4675 lp->infoblock_csr6 = OMR_SIA;
4678 de4x5_switch_mac_port(dev);
4681 return dc2114x_autoconf(dev);
4685 type3_infoblock(struct net_device *dev, u_char count, u_char *p)
4687 struct de4x5_private *lp = netdev_priv(dev);
4688 u_char len = (*p & BLOCK_LEN)+1;
4690 /* Recursively figure out the info blocks */
4691 if (--count > lp->tcount) {
4692 if (*(p+len) < 128) {
4693 return dc_infoblock[COMPACT](dev, count, p+len);
4695 return dc_infoblock[*(p+len+1)](dev, count, p+len);
4700 if (lp->state == INITIALISED) {
4703 if (MOTO_SROM_BUG) lp->active = 0;
4704 /* if (MOTO_SROM_BUG) statement indicates lp->active could
4705 * be 8 (i.e. the size of array lp->phy) */
4706 if (WARN_ON(lp->active >= ARRAY_SIZE(lp->phy)))
4708 lp->phy[lp->active].gep = (*p ? p : NULL); p += (2 * (*p) + 1);
4709 lp->phy[lp->active].rst = (*p ? p : NULL); p += (2 * (*p) + 1);
4710 lp->phy[lp->active].mc = get_unaligned_le16(p); p += 2;
4711 lp->phy[lp->active].ana = get_unaligned_le16(p); p += 2;
4712 lp->phy[lp->active].fdx = get_unaligned_le16(p); p += 2;
4713 lp->phy[lp->active].ttm = get_unaligned_le16(p); p += 2;
4714 lp->phy[lp->active].mci = *p;
4716 } else if ((lp->media == INIT) && (lp->timeout < 0)) {
4719 if (MOTO_SROM_BUG) lp->active = 0;
4720 lp->infoblock_csr6 = OMR_MII_100;
4722 lp->infoblock_media = ANS;
4724 de4x5_switch_mac_port(dev);
4727 return dc2114x_autoconf(dev);
4731 type4_infoblock(struct net_device *dev, u_char count, u_char *p)
4733 struct de4x5_private *lp = netdev_priv(dev);
4734 u_char flags, csr6, len = (*p & BLOCK_LEN)+1;
4736 /* Recursively figure out the info blocks */
4737 if (--count > lp->tcount) {
4738 if (*(p+len) < 128) {
4739 return dc_infoblock[COMPACT](dev, count, p+len);
4741 return dc_infoblock[*(p+len+1)](dev, count, p+len);
4745 if ((lp->media == INIT) && (lp->timeout < 0)) {
4749 lp->infoblock_media = (*p++) & MEDIA_CODE;
4750 lp->cache.csr13 = CSR13; /* Hard coded defaults */
4751 lp->cache.csr14 = CSR14;
4752 lp->cache.csr15 = CSR15;
4753 lp->cache.gepc = ((s32)(get_unaligned_le16(p)) << 16); p += 2;
4754 lp->cache.gep = ((s32)(get_unaligned_le16(p)) << 16); p += 2;
4758 lp->asBitValid = (flags & 0x80) ? 0 : -1;
4759 lp->defMedium = (flags & 0x40) ? -1 : 0;
4760 lp->asBit = 1 << ((csr6 >> 1) & 0x07);
4761 lp->asPolarity = ((csr6 & 0x80) ? -1 : 0) & lp->asBit;
4762 lp->infoblock_csr6 = OMR_DEF | ((csr6 & 0x71) << 18);
4765 de4x5_switch_mac_port(dev);
4768 return dc2114x_autoconf(dev);
4772 ** This block type provides information for resetting external devices
4773 ** (chips) through the General Purpose Register.
4776 type5_infoblock(struct net_device *dev, u_char count, u_char *p)
4778 struct de4x5_private *lp = netdev_priv(dev);
4779 u_char len = (*p & BLOCK_LEN)+1;
4781 /* Recursively figure out the info blocks */
4782 if (--count > lp->tcount) {
4783 if (*(p+len) < 128) {
4784 return dc_infoblock[COMPACT](dev, count, p+len);
4786 return dc_infoblock[*(p+len+1)](dev, count, p+len);
4790 /* Must be initializing to run this code */
4791 if ((lp->state == INITIALISED) || (lp->media == INIT)) {
4794 srom_exec(dev, lp->rst);
4797 return DE4X5_AUTOSENSE_MS;
4805 mii_rd(u_char phyreg, u_char phyaddr, u_long ioaddr)
4807 mii_wdata(MII_PREAMBLE, 2, ioaddr); /* Start of 34 bit preamble... */
4808 mii_wdata(MII_PREAMBLE, 32, ioaddr); /* ...continued */
4809 mii_wdata(MII_STRD, 4, ioaddr); /* SFD and Read operation */
4810 mii_address(phyaddr, ioaddr); /* PHY address to be accessed */
4811 mii_address(phyreg, ioaddr); /* PHY Register to read */
4812 mii_ta(MII_STRD, ioaddr); /* Turn around time - 2 MDC */
4814 return mii_rdata(ioaddr); /* Read data */
4818 mii_wr(int data, u_char phyreg, u_char phyaddr, u_long ioaddr)
4820 mii_wdata(MII_PREAMBLE, 2, ioaddr); /* Start of 34 bit preamble... */
4821 mii_wdata(MII_PREAMBLE, 32, ioaddr); /* ...continued */
4822 mii_wdata(MII_STWR, 4, ioaddr); /* SFD and Write operation */
4823 mii_address(phyaddr, ioaddr); /* PHY address to be accessed */
4824 mii_address(phyreg, ioaddr); /* PHY Register to write */
4825 mii_ta(MII_STWR, ioaddr); /* Turn around time - 2 MDC */
4826 data = mii_swap(data, 16); /* Swap data bit ordering */
4827 mii_wdata(data, 16, ioaddr); /* Write data */
4831 mii_rdata(u_long ioaddr)
4836 for (i=0; i<16; i++) {
4838 tmp |= getfrom_mii(MII_MRD | MII_RD, ioaddr);
4845 mii_wdata(int data, int len, u_long ioaddr)
4849 for (i=0; i<len; i++) {
4850 sendto_mii(MII_MWR | MII_WR, data, ioaddr);
4856 mii_address(u_char addr, u_long ioaddr)
4860 addr = mii_swap(addr, 5);
4861 for (i=0; i<5; i++) {
4862 sendto_mii(MII_MWR | MII_WR, addr, ioaddr);
4868 mii_ta(u_long rw, u_long ioaddr)
4870 if (rw == MII_STWR) {
4871 sendto_mii(MII_MWR | MII_WR, 1, ioaddr);
4872 sendto_mii(MII_MWR | MII_WR, 0, ioaddr);
4874 getfrom_mii(MII_MRD | MII_RD, ioaddr); /* Tri-state MDIO */
4879 mii_swap(int data, int len)
4883 for (i=0; i<len; i++) {
4893 sendto_mii(u32 command, int data, u_long ioaddr)
4897 j = (data & 1) << 17;
4898 outl(command | j, ioaddr);
4900 outl(command | MII_MDC | j, ioaddr);
4905 getfrom_mii(u32 command, u_long ioaddr)
4907 outl(command, ioaddr);
4909 outl(command | MII_MDC, ioaddr);
4912 return (inl(ioaddr) >> 19) & 1;
4916 ** Here's 3 ways to calculate the OUI from the ID registers.
4919 mii_get_oui(u_char phyaddr, u_long ioaddr)
4926 int i, r2, r3, ret=0;*/
4929 /* Read r2 and r3 */
4930 r2 = mii_rd(MII_ID0, phyaddr, ioaddr);
4931 r3 = mii_rd(MII_ID1, phyaddr, ioaddr);
4932 /* SEEQ and Cypress way * /
4933 / * Shuffle r2 and r3 * /
4935 r3 = ((r3>>10)|(r2<<6))&0x0ff;
4936 r2 = ((r2>>2)&0x3fff);
4938 / * Bit reverse r3 * /
4945 / * Bit reverse r2 * /
4946 for (i=0;i<16;i++) {
4952 / * Swap r2 bytes * /
4954 a.breg[0]=a.breg[1];
4957 return (a.reg<<8)|ret; */ /* SEEQ and Cypress way */
4958 /* return (r2<<6)|(u_int)(r3>>10); */ /* NATIONAL and BROADCOM way */
4959 return r2; /* (I did it) My way */
4963 ** The SROM spec forces us to search addresses [1-31 0]. Bummer.
4966 mii_get_phy(struct net_device *dev)
4968 struct de4x5_private *lp = netdev_priv(dev);
4969 u_long iobase = dev->base_addr;
4970 int i, j, k, n, limit=ARRAY_SIZE(phy_info);
4976 /* Search the MII address space for possible PHY devices */
4977 for (n=0, lp->mii_cnt=0, i=1; !((i==1) && (n==1)); i=(i+1)%DE4X5_MAX_MII) {
4978 lp->phy[lp->active].addr = i;
4979 if (i==0) n++; /* Count cycles */
4980 while (de4x5_reset_phy(dev)<0) udelay(100);/* Wait for reset */
4981 id = mii_get_oui(i, DE4X5_MII);
4982 if ((id == 0) || (id == 65535)) continue; /* Valid ID? */
4983 for (j=0; j<limit; j++) { /* Search PHY table */
4984 if (id != phy_info[j].id) continue; /* ID match? */
4985 for (k=0; k < DE4X5_MAX_PHY && lp->phy[k].id; k++);
4986 if (k < DE4X5_MAX_PHY) {
4987 memcpy((char *)&lp->phy[k],
4988 (char *)&phy_info[j], sizeof(struct phy_table));
4989 lp->phy[k].addr = i;
4993 goto purgatory; /* Stop the search */
4997 if ((j == limit) && (i < DE4X5_MAX_MII)) {
4998 for (k=0; k < DE4X5_MAX_PHY && lp->phy[k].id; k++);
4999 if (k < DE4X5_MAX_PHY) {
5000 lp->phy[k].addr = i;
5002 lp->phy[k].spd.reg = GENERIC_REG; /* ANLPA register */
5003 lp->phy[k].spd.mask = GENERIC_MASK; /* 100Mb/s technologies */
5004 lp->phy[k].spd.value = GENERIC_VALUE; /* TX & T4, H/F Duplex */
5007 printk("%s: Using generic MII device control. If the board doesn't operate,\nplease mail the following dump to the author:\n", dev->name);
5009 de4x5_debug |= DEBUG_MII;
5010 de4x5_dbg_mii(dev, k);
5020 if (lp->phy[0].id) { /* Reset the PHY devices */
5021 for (k=0; k < DE4X5_MAX_PHY && lp->phy[k].id; k++) { /*For each PHY*/
5022 mii_wr(MII_CR_RST, MII_CR, lp->phy[k].addr, DE4X5_MII);
5023 while (mii_rd(MII_CR, lp->phy[k].addr, DE4X5_MII) & MII_CR_RST);
5025 de4x5_dbg_mii(dev, k);
5028 if (!lp->mii_cnt) lp->useMII = false;
5034 build_setup_frame(struct net_device *dev, int mode)
5036 struct de4x5_private *lp = netdev_priv(dev);
5038 char *pa = lp->setup_frame;
5040 /* Initialise the setup frame */
5042 memset(lp->setup_frame, 0, SETUP_FRAME_LEN);
5045 if (lp->setup_f == HASH_PERF) {
5046 for (pa=lp->setup_frame+IMPERF_PA_OFFSET, i=0; i<ETH_ALEN; i++) {
5047 *(pa + i) = dev->dev_addr[i]; /* Host address */
5048 if (i & 0x01) pa += 2;
5050 *(lp->setup_frame + (HASH_TABLE_LEN >> 3) - 3) = 0x80;
5052 for (i=0; i<ETH_ALEN; i++) { /* Host address */
5053 *(pa + (i&1)) = dev->dev_addr[i];
5054 if (i & 0x01) pa += 4;
5056 for (i=0; i<ETH_ALEN; i++) { /* Broadcast address */
5057 *(pa + (i&1)) = (char) 0xff;
5058 if (i & 0x01) pa += 4;
5062 return pa; /* Points to the next entry */
5066 disable_ast(struct net_device *dev)
5068 struct de4x5_private *lp = netdev_priv(dev);
5069 del_timer_sync(&lp->timer);
5073 de4x5_switch_mac_port(struct net_device *dev)
5075 struct de4x5_private *lp = netdev_priv(dev);
5076 u_long iobase = dev->base_addr;
5081 /* Assert the OMR_PS bit in CSR6 */
5082 omr = (inl(DE4X5_OMR) & ~(OMR_PS | OMR_HBD | OMR_TTM | OMR_PCS | OMR_SCR |
5084 omr |= lp->infoblock_csr6;
5085 if (omr & OMR_PS) omr |= OMR_HBD;
5086 outl(omr, DE4X5_OMR);
5091 /* Restore the GEP - especially for COMPACT and Type 0 Infoblocks */
5092 if (lp->chipset == DC21140) {
5093 gep_wr(lp->cache.gepc, dev);
5094 gep_wr(lp->cache.gep, dev);
5095 } else if ((lp->chipset & ~0x0ff) == DC2114x) {
5096 reset_init_sia(dev, lp->cache.csr13, lp->cache.csr14, lp->cache.csr15);
5100 outl(omr, DE4X5_OMR);
5109 gep_wr(s32 data, struct net_device *dev)
5111 struct de4x5_private *lp = netdev_priv(dev);
5112 u_long iobase = dev->base_addr;
5114 if (lp->chipset == DC21140) {
5115 outl(data, DE4X5_GEP);
5116 } else if ((lp->chipset & ~0x00ff) == DC2114x) {
5117 outl((data<<16) | lp->cache.csr15, DE4X5_SIGR);
5122 gep_rd(struct net_device *dev)
5124 struct de4x5_private *lp = netdev_priv(dev);
5125 u_long iobase = dev->base_addr;
5127 if (lp->chipset == DC21140) {
5128 return inl(DE4X5_GEP);
5129 } else if ((lp->chipset & ~0x00ff) == DC2114x) {
5130 return inl(DE4X5_SIGR) & 0x000fffff;
5137 yawn(struct net_device *dev, int state)
5139 struct de4x5_private *lp = netdev_priv(dev);
5140 u_long iobase = dev->base_addr;
5142 if ((lp->chipset == DC21040) || (lp->chipset == DC21140)) return;
5144 if(lp->bus == EISA) {
5147 outb(WAKEUP, PCI_CFPM);
5152 outb(SNOOZE, PCI_CFPM);
5156 outl(0, DE4X5_SICR);
5157 outb(SLEEP, PCI_CFPM);
5161 struct pci_dev *pdev = to_pci_dev (lp->gendev);
5164 pci_write_config_byte(pdev, PCI_CFDA_PSM, WAKEUP);
5169 pci_write_config_byte(pdev, PCI_CFDA_PSM, SNOOZE);
5173 outl(0, DE4X5_SICR);
5174 pci_write_config_byte(pdev, PCI_CFDA_PSM, SLEEP);
5181 de4x5_parse_params(struct net_device *dev)
5183 struct de4x5_private *lp = netdev_priv(dev);
5186 lp->params.fdx = false;
5187 lp->params.autosense = AUTO;
5189 if (args == NULL) return;
5191 if ((p = strstr(args, dev->name))) {
5192 if (!(q = strstr(p+strlen(dev->name), "eth"))) q = p + strlen(p);
5196 if (strstr(p, "fdx") || strstr(p, "FDX")) lp->params.fdx = true;
5198 if (strstr(p, "autosense") || strstr(p, "AUTOSENSE")) {
5199 if (strstr(p, "TP_NW")) {
5200 lp->params.autosense = TP_NW;
5201 } else if (strstr(p, "TP")) {
5202 lp->params.autosense = TP;
5203 } else if (strstr(p, "BNC_AUI")) {
5204 lp->params.autosense = BNC;
5205 } else if (strstr(p, "BNC")) {
5206 lp->params.autosense = BNC;
5207 } else if (strstr(p, "AUI")) {
5208 lp->params.autosense = AUI;
5209 } else if (strstr(p, "10Mb")) {
5210 lp->params.autosense = _10Mb;
5211 } else if (strstr(p, "100Mb")) {
5212 lp->params.autosense = _100Mb;
5213 } else if (strstr(p, "AUTO")) {
5214 lp->params.autosense = AUTO;
5222 de4x5_dbg_open(struct net_device *dev)
5224 struct de4x5_private *lp = netdev_priv(dev);
5227 if (de4x5_debug & DEBUG_OPEN) {
5228 printk("%s: de4x5 opening with irq %d\n",dev->name,dev->irq);
5229 printk("\tphysical address: %pM\n", dev->dev_addr);
5230 printk("Descriptor head addresses:\n");
5231 printk("\t0x%8.8lx 0x%8.8lx\n",(u_long)lp->rx_ring,(u_long)lp->tx_ring);
5232 printk("Descriptor addresses:\nRX: ");
5233 for (i=0;i<lp->rxRingSize-1;i++){
5235 printk("0x%8.8lx ",(u_long)&lp->rx_ring[i].status);
5238 printk("...0x%8.8lx\n",(u_long)&lp->rx_ring[i].status);
5240 for (i=0;i<lp->txRingSize-1;i++){
5242 printk("0x%8.8lx ", (u_long)&lp->tx_ring[i].status);
5245 printk("...0x%8.8lx\n", (u_long)&lp->tx_ring[i].status);
5246 printk("Descriptor buffers:\nRX: ");
5247 for (i=0;i<lp->rxRingSize-1;i++){
5249 printk("0x%8.8x ",le32_to_cpu(lp->rx_ring[i].buf));
5252 printk("...0x%8.8x\n",le32_to_cpu(lp->rx_ring[i].buf));
5254 for (i=0;i<lp->txRingSize-1;i++){
5256 printk("0x%8.8x ", le32_to_cpu(lp->tx_ring[i].buf));
5259 printk("...0x%8.8x\n", le32_to_cpu(lp->tx_ring[i].buf));
5260 printk("Ring size:\nRX: %d\nTX: %d\n",
5261 (short)lp->rxRingSize,
5262 (short)lp->txRingSize);
5267 de4x5_dbg_mii(struct net_device *dev, int k)
5269 struct de4x5_private *lp = netdev_priv(dev);
5270 u_long iobase = dev->base_addr;
5272 if (de4x5_debug & DEBUG_MII) {
5273 printk("\nMII device address: %d\n", lp->phy[k].addr);
5274 printk("MII CR: %x\n",mii_rd(MII_CR,lp->phy[k].addr,DE4X5_MII));
5275 printk("MII SR: %x\n",mii_rd(MII_SR,lp->phy[k].addr,DE4X5_MII));
5276 printk("MII ID0: %x\n",mii_rd(MII_ID0,lp->phy[k].addr,DE4X5_MII));
5277 printk("MII ID1: %x\n",mii_rd(MII_ID1,lp->phy[k].addr,DE4X5_MII));
5278 if (lp->phy[k].id != BROADCOM_T4) {
5279 printk("MII ANA: %x\n",mii_rd(0x04,lp->phy[k].addr,DE4X5_MII));
5280 printk("MII ANC: %x\n",mii_rd(0x05,lp->phy[k].addr,DE4X5_MII));
5282 printk("MII 16: %x\n",mii_rd(0x10,lp->phy[k].addr,DE4X5_MII));
5283 if (lp->phy[k].id != BROADCOM_T4) {
5284 printk("MII 17: %x\n",mii_rd(0x11,lp->phy[k].addr,DE4X5_MII));
5285 printk("MII 18: %x\n",mii_rd(0x12,lp->phy[k].addr,DE4X5_MII));
5287 printk("MII 20: %x\n",mii_rd(0x14,lp->phy[k].addr,DE4X5_MII));
5293 de4x5_dbg_media(struct net_device *dev)
5295 struct de4x5_private *lp = netdev_priv(dev);
5297 if (lp->media != lp->c_media) {
5298 if (de4x5_debug & DEBUG_MEDIA) {
5299 printk("%s: media is %s%s\n", dev->name,
5300 (lp->media == NC ? "unconnected, link down or incompatible connection" :
5301 (lp->media == TP ? "TP" :
5302 (lp->media == ANS ? "TP/Nway" :
5303 (lp->media == BNC ? "BNC" :
5304 (lp->media == AUI ? "AUI" :
5305 (lp->media == BNC_AUI ? "BNC/AUI" :
5306 (lp->media == EXT_SIA ? "EXT SIA" :
5307 (lp->media == _100Mb ? "100Mb/s" :
5308 (lp->media == _10Mb ? "10Mb/s" :
5310 ))))))))), (lp->fdx?" full duplex.":"."));
5312 lp->c_media = lp->media;
5317 de4x5_dbg_srom(struct de4x5_srom *p)
5321 if (de4x5_debug & DEBUG_SROM) {
5322 printk("Sub-system Vendor ID: %04x\n", *((u_short *)p->sub_vendor_id));
5323 printk("Sub-system ID: %04x\n", *((u_short *)p->sub_system_id));
5324 printk("ID Block CRC: %02x\n", (u_char)(p->id_block_crc));
5325 printk("SROM version: %02x\n", (u_char)(p->version));
5326 printk("# controllers: %02x\n", (u_char)(p->num_controllers));
5328 printk("Hardware Address: %pM\n", p->ieee_addr);
5329 printk("CRC checksum: %04x\n", (u_short)(p->chksum));
5330 for (i=0; i<64; i++) {
5331 printk("%3d %04x\n", i<<1, (u_short)*((u_short *)p+i));
5337 de4x5_dbg_rx(struct sk_buff *skb, int len)
5341 if (de4x5_debug & DEBUG_RX) {
5342 printk("R: %pM <- %pM len/SAP:%02x%02x [%d]\n",
5343 skb->data, &skb->data[6],
5344 (u_char)skb->data[12],
5345 (u_char)skb->data[13],
5347 for (j=0; len>0;j+=16, len-=16) {
5348 printk(" %03x: ",j);
5349 for (i=0; i<16 && i<len; i++) {
5350 printk("%02x ",(u_char)skb->data[i+j]);
5358 ** Perform IOCTL call functions here. Some are privileged operations and the
5359 ** effective uid is checked in those cases. In the normal course of events
5360 ** this function is only used for my testing.
5363 de4x5_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
5365 struct de4x5_private *lp = netdev_priv(dev);
5366 struct de4x5_ioctl *ioc = (struct de4x5_ioctl *) &rq->ifr_ifru;
5367 u_long iobase = dev->base_addr;
5368 int i, j, status = 0;
5378 case DE4X5_GET_HWADDR: /* Get the hardware address */
5379 ioc->len = ETH_ALEN;
5380 for (i=0; i<ETH_ALEN; i++) {
5381 tmp.addr[i] = dev->dev_addr[i];
5383 if (copy_to_user(ioc->data, tmp.addr, ioc->len)) return -EFAULT;
5386 case DE4X5_SET_HWADDR: /* Set the hardware address */
5387 if (!capable(CAP_NET_ADMIN)) return -EPERM;
5388 if (copy_from_user(tmp.addr, ioc->data, ETH_ALEN)) return -EFAULT;
5389 if (netif_queue_stopped(dev))
5391 netif_stop_queue(dev);
5392 for (i=0; i<ETH_ALEN; i++) {
5393 dev->dev_addr[i] = tmp.addr[i];
5395 build_setup_frame(dev, PHYS_ADDR_ONLY);
5396 /* Set up the descriptor and give ownership to the card */
5397 load_packet(dev, lp->setup_frame, TD_IC | PERFECT_F | TD_SET |
5398 SETUP_FRAME_LEN, (struct sk_buff *)1);
5399 lp->tx_new = (lp->tx_new + 1) % lp->txRingSize;
5400 outl(POLL_DEMAND, DE4X5_TPD); /* Start the TX */
5401 netif_wake_queue(dev); /* Unlock the TX ring */
5404 case DE4X5_SAY_BOO: /* Say "Boo!" to the kernel log file */
5405 if (!capable(CAP_NET_ADMIN)) return -EPERM;
5406 printk("%s: Boo!\n", dev->name);
5409 case DE4X5_MCA_EN: /* Enable pass all multicast addressing */
5410 if (!capable(CAP_NET_ADMIN)) return -EPERM;
5411 omr = inl(DE4X5_OMR);
5413 outl(omr, DE4X5_OMR);
5416 case DE4X5_GET_STATS: /* Get the driver statistics */
5418 struct pkt_stats statbuf;
5419 ioc->len = sizeof(statbuf);
5420 spin_lock_irqsave(&lp->lock, flags);
5421 memcpy(&statbuf, &lp->pktStats, ioc->len);
5422 spin_unlock_irqrestore(&lp->lock, flags);
5423 if (copy_to_user(ioc->data, &statbuf, ioc->len))
5427 case DE4X5_CLR_STATS: /* Zero out the driver statistics */
5428 if (!capable(CAP_NET_ADMIN)) return -EPERM;
5429 spin_lock_irqsave(&lp->lock, flags);
5430 memset(&lp->pktStats, 0, sizeof(lp->pktStats));
5431 spin_unlock_irqrestore(&lp->lock, flags);
5434 case DE4X5_GET_OMR: /* Get the OMR Register contents */
5435 tmp.addr[0] = inl(DE4X5_OMR);
5436 if (copy_to_user(ioc->data, tmp.addr, 1)) return -EFAULT;
5439 case DE4X5_SET_OMR: /* Set the OMR Register contents */
5440 if (!capable(CAP_NET_ADMIN)) return -EPERM;
5441 if (copy_from_user(tmp.addr, ioc->data, 1)) return -EFAULT;
5442 outl(tmp.addr[0], DE4X5_OMR);
5445 case DE4X5_GET_REG: /* Get the DE4X5 Registers */
5447 tmp.lval[0] = inl(DE4X5_STS); j+=4;
5448 tmp.lval[1] = inl(DE4X5_BMR); j+=4;
5449 tmp.lval[2] = inl(DE4X5_IMR); j+=4;
5450 tmp.lval[3] = inl(DE4X5_OMR); j+=4;
5451 tmp.lval[4] = inl(DE4X5_SISR); j+=4;
5452 tmp.lval[5] = inl(DE4X5_SICR); j+=4;
5453 tmp.lval[6] = inl(DE4X5_STRR); j+=4;
5454 tmp.lval[7] = inl(DE4X5_SIGR); j+=4;
5456 if (copy_to_user(ioc->data, tmp.lval, ioc->len))
5460 #define DE4X5_DUMP 0x0f /* Dump the DE4X5 Status */
5464 tmp.addr[j++] = dev->irq;
5465 for (i=0; i<ETH_ALEN; i++) {
5466 tmp.addr[j++] = dev->dev_addr[i];
5468 tmp.addr[j++] = lp->rxRingSize;
5469 tmp.lval[j>>2] = (long)lp->rx_ring; j+=4;
5470 tmp.lval[j>>2] = (long)lp->tx_ring; j+=4;
5472 for (i=0;i<lp->rxRingSize-1;i++){
5474 tmp.lval[j>>2] = (long)&lp->rx_ring[i].status; j+=4;
5477 tmp.lval[j>>2] = (long)&lp->rx_ring[i].status; j+=4;
5478 for (i=0;i<lp->txRingSize-1;i++){
5480 tmp.lval[j>>2] = (long)&lp->tx_ring[i].status; j+=4;
5483 tmp.lval[j>>2] = (long)&lp->tx_ring[i].status; j+=4;
5485 for (i=0;i<lp->rxRingSize-1;i++){
5487 tmp.lval[j>>2] = (s32)le32_to_cpu(lp->rx_ring[i].buf); j+=4;
5490 tmp.lval[j>>2] = (s32)le32_to_cpu(lp->rx_ring[i].buf); j+=4;
5491 for (i=0;i<lp->txRingSize-1;i++){
5493 tmp.lval[j>>2] = (s32)le32_to_cpu(lp->tx_ring[i].buf); j+=4;
5496 tmp.lval[j>>2] = (s32)le32_to_cpu(lp->tx_ring[i].buf); j+=4;
5498 for (i=0;i<lp->rxRingSize;i++){
5499 tmp.lval[j>>2] = le32_to_cpu(lp->rx_ring[i].status); j+=4;
5501 for (i=0;i<lp->txRingSize;i++){
5502 tmp.lval[j>>2] = le32_to_cpu(lp->tx_ring[i].status); j+=4;
5505 tmp.lval[j>>2] = inl(DE4X5_BMR); j+=4;
5506 tmp.lval[j>>2] = inl(DE4X5_TPD); j+=4;
5507 tmp.lval[j>>2] = inl(DE4X5_RPD); j+=4;
5508 tmp.lval[j>>2] = inl(DE4X5_RRBA); j+=4;
5509 tmp.lval[j>>2] = inl(DE4X5_TRBA); j+=4;
5510 tmp.lval[j>>2] = inl(DE4X5_STS); j+=4;
5511 tmp.lval[j>>2] = inl(DE4X5_OMR); j+=4;
5512 tmp.lval[j>>2] = inl(DE4X5_IMR); j+=4;
5513 tmp.lval[j>>2] = lp->chipset; j+=4;
5514 if (lp->chipset == DC21140) {
5515 tmp.lval[j>>2] = gep_rd(dev); j+=4;
5517 tmp.lval[j>>2] = inl(DE4X5_SISR); j+=4;
5518 tmp.lval[j>>2] = inl(DE4X5_SICR); j+=4;
5519 tmp.lval[j>>2] = inl(DE4X5_STRR); j+=4;
5520 tmp.lval[j>>2] = inl(DE4X5_SIGR); j+=4;
5522 tmp.lval[j>>2] = lp->phy[lp->active].id; j+=4;
5523 if (lp->phy[lp->active].id && (!lp->useSROM || lp->useMII)) {
5524 tmp.lval[j>>2] = lp->active; j+=4;
5525 tmp.lval[j>>2]=mii_rd(MII_CR,lp->phy[lp->active].addr,DE4X5_MII); j+=4;
5526 tmp.lval[j>>2]=mii_rd(MII_SR,lp->phy[lp->active].addr,DE4X5_MII); j+=4;
5527 tmp.lval[j>>2]=mii_rd(MII_ID0,lp->phy[lp->active].addr,DE4X5_MII); j+=4;
5528 tmp.lval[j>>2]=mii_rd(MII_ID1,lp->phy[lp->active].addr,DE4X5_MII); j+=4;
5529 if (lp->phy[lp->active].id != BROADCOM_T4) {
5530 tmp.lval[j>>2]=mii_rd(MII_ANA,lp->phy[lp->active].addr,DE4X5_MII); j+=4;
5531 tmp.lval[j>>2]=mii_rd(MII_ANLPA,lp->phy[lp->active].addr,DE4X5_MII); j+=4;
5533 tmp.lval[j>>2]=mii_rd(0x10,lp->phy[lp->active].addr,DE4X5_MII); j+=4;
5534 if (lp->phy[lp->active].id != BROADCOM_T4) {
5535 tmp.lval[j>>2]=mii_rd(0x11,lp->phy[lp->active].addr,DE4X5_MII); j+=4;
5536 tmp.lval[j>>2]=mii_rd(0x12,lp->phy[lp->active].addr,DE4X5_MII); j+=4;
5538 tmp.lval[j>>2]=mii_rd(0x14,lp->phy[lp->active].addr,DE4X5_MII); j+=4;
5542 tmp.addr[j++] = lp->txRingSize;
5543 tmp.addr[j++] = netif_queue_stopped(dev);
5546 if (copy_to_user(ioc->data, tmp.addr, ioc->len)) return -EFAULT;
5557 static int __init de4x5_module_init (void)
5562 err = pci_register_driver(&de4x5_pci_driver);
5565 err |= eisa_driver_register (&de4x5_eisa_driver);
5571 static void __exit de4x5_module_exit (void)
5574 pci_unregister_driver (&de4x5_pci_driver);
5577 eisa_driver_unregister (&de4x5_eisa_driver);
5581 module_init (de4x5_module_init);
5582 module_exit (de4x5_module_exit);